Re: Interfacing PS and PL (streaming data from PS to PL)
So your suggestion is to make my own AXI Slave IP instead of axi_dmac_v1_0? Is there way that I can lower data rate? I would like to get suggestion. Basically I need to enable controlled streaming of...
View ArticleRe: Interfacing PS and PL (streaming data from PS to PL)
No, I never said that yet. There are too many things I don't know about your specific application, so I can't really offer advice. For example - what most people do is put symbol <-> sample...
View ArticleRe: AD5683 Headroom/Footroom Error
Hi Miguel, It is as follows. *****************************************************************I understand you mentioned.I just want to make sure as follows.1)The characteristics of 0x0000 between 0mA...
View ArticleClik here to view.
Re: Interfacing PS and PL (streaming data from PS to PL)
Dear Robin, Basically what I want to do is: 1. Connect zedboard via ethernet and feed my transceiver implemented on PL by data for computer. (but this is at the end) I bring OS on PS and I have...
View ArticleRe: Internal Protection for ADuCM361?
Hi Bindu, I moved your question to the ADuC Cortex M3 community. Someone here should be able to assist you. Thanks!Kris
View ArticleClik here to view.
Re: SSM2604 SR setting
Hi Dave, Thank you very much for your detail reply. Best regards,Nikkee
View ArticleParameter P1dB of attenuator HMC629LP4E
Hi,I read in the datasheet of attenuator HMC629LP4E, but I cannot find the parameters P1dB and IIP3. Could tell me these parameters of this IC, please Thank you very much! Hieu Dam.
View ArticleRe: ADF7242 stopped the operation of Rx
Hi rbrennan Thank you for your reply.I got it. Regards,
View ArticleADF5355
Hello,ADF5355 - any updates for Simpll? especially regarding spurs calc in fractional mode...Output power for frequencies from 50MHz to 1GHz?Simpll missing output doubler...Anyway to decrease settling...
View ArticleRe: AD7291 Temperature reading not stable
Hi GuiX, With these updated values, it is recommended that the ground plane of the board should be tied as close as possible to the device GND and GND1 pin. Proper grounding should always be...
View ArticleAre there plans to support BF70X for linux distribution for blackfin
Hi all, We are planning to develop the new products using BF70X with linux distribution. But, I can't find the linux distribution which supports BF70X in the official website. Are you developing...
View ArticleRe: Echo Canceller for SigmaDSP
Hi Tin Tin, Brett is no longer with Analog Devices. I will respond to your question on echo cancellation documentation in the other thread: ADI Sigma DSP for echo cancellation -JT
View ArticleClik here to view.
Re: ADM1278 address setting
I do not understanding about this figure 52.Would you kindly help me explain it. Specifically PSET
View ArticleADV7280-M video capture issue with i.MX6Q
Hi all, We are trying to interface the ADV7280-M with the i.MX6Q processor. Our Linux driver follows the registersettings described in the 'I2P AUTODETECT CVBS Single Ended In Ain 1, 480p/576p MIPI...
View ArticleClik here to view.
Re: Series or Shunt Voltage Reference for AD5546
I will be moving this inquiry to the Precision DACs Community. When selecting a reference, pay attention to the output voltage temperature coefficient specification of the reference. Choosing a...
View ArticleRe: Is there something wrong in the data sheet of AD650
Some quick thoughts before going out the door:-- Run on +/-12V-- look for a different FET-- Use a logic family that runs on 3.3VHarry
View ArticleRe: AD7176-2 RDY
Hi Terumasa, The scan rate is the max rate at which you can multiplex between channels. If the output data rate is 250 ksps and the sinc5+sinc1 filter is used, the settling time is 20 us. So, you can...
View ArticleRe: AD7195 conversion question
Hi Petervers,When internal calibrations are performed, the offset register is always close to 800000 hex and the full scale register is 5XXXXX. With a shorted input and DC excitation, the output...
View ArticleRe: How to diagnose a non-responsive AD-FMDADC2 board connected to a Zynq706?
Hi Robin, Please, refer to the original post, as shown above, in which I put a screenshot of the AD IIO application. The problem we have is that under the AD IIO capture application, no device is...
View Article