Re: ADV7280-M video capture issue with i.MX6Q
Hello Robert, Thank you for your reply. I do have AN-1337 thank you I think we are reasonably happy that the interface with the i.MX6Q MIPI CSI-2 receiver is configured correctly because we have no...
View ArticleADXL362 Noise Density in Wake-Up Mode
Hi I need detail information about Noise Density of ADXL362.To decide threshold of motion detecting, I have two questions. 1. ODR of Wake-Up mode is 6Hz, but the ODR defined in BANDWIDTH is 12.5Hz to...
View ArticleRe: EV AD9910 Output Filter
Hi,Can you also check the SMA cables that you used? I suggest, you use much better cables. For a crystal of 25MHz, may I know your loop filter values?
View ArticleRe: Can ADuM4160 Detect Device Removal Event as A Peripheral?
Thanks for your answer. I want to make my user to know the "link" broken stated. And for the isolation purpose, I think using an optocoupler to detect the Vbus state and route the signal to MCU is a...
View ArticleRe: Motorized Lens Control
Hello Yehiel,This Motor Control Hardware platforms page covers industrial motor drives rather than small motors such as this lens motor. However, I did check with the consumer applications team and...
View ArticleClik here to view.
Re: ADE7816 ANGLEx
Hi hmani Thank's for your reply. 1. I verify the source by measuring with Lutron Digital KWH Meter. The load is 18W flourescent bulb, Lutron shows 19W and pF is 0.6. I use CT current sensor with Rb 51...
View ArticleRe: AD7091R-4 offset
Hi Karen, Please update this thread.Our customer must decide if he uses AD7091R-4 or another device and he needs this informatoin for decision.Please let me know your advice. Regards,Terumasa
View ArticleRe: AD9364 tx inverted
Dragos, Thanks for the testing.On my AD-FMCCOMMS4-EBZ the tx still inverted, and there is no change if I manually set the Invert TX1 bit from register 011. Here I attach my init parameters and dev...
View ArticleRe: Evaluation Software can not see AD9912A/PCBZ
This usually happens when the VID/PID loaded is different from what is supposed to be loaded. Can you compare the VID/PID on both cases, if they are indeed different? You can do that by accessing the...
View ArticleRe: Spurs at EV of AD9910
Hi Meir, I didn't thought that you were using a PLL. Our spectrum plot were taken without using it. Can you try shielding the power supply or turning off some other equipment in your lab that you are...
View ArticleRe: SHARC ADSP-21489 SPI slave transmitting extra leading zero byte
Dave,can you post the relevant code and some scope traces?Without that it will be difficult to see what might be going on...Klaus
View ArticleRe: Question
Hi Anson, Yes, it has to be connected. You can use the SPI interface for it and the links in the board to implement physically the Arduino to AD5933EBZ. Best RegardsLouijie
View ArticleTrouble programming AD5932 Evaluation Board
The trouble is that I can not seem to establish communication with the device using the DLL posted here.AD5930 and AD5932 evaluation board software commands Miguel has been working with me, but I...
View ArticleRe: hardware trace infomation differ with the "bfin-linux-uclibc-objdump -d"...
Could you share us schematics for your ethernet MAC/PHY connection?
View ArticleHMC625ALP5E vs HMC625HFLP5E
G'day, We have previously used the HMC625HFLP5E (now marked obsolete).The alternative part HMC625ALP5E is mostly the same except for the addition of the ACG1 - ACG6 pins (where previously they were...
View ArticleClik here to view.
Re: Questions about AD9257
Hi Tak-san, Yes, the effect of jitter discussed on page 22 of the AD9257 datasheet is related to sampling, which on the AD9257 is at the rising edge.A jittery clock will probably have jitter on both...
View Articlefmcomms data rates
Does anyone have any benchmark data on realistically achievable rx and tx sample rates with the IIO linux drivers on a zynq platform?
View ArticleWhat causes the "SS_CMD_BK_ERROR_CODE" case in "BackChannelProcess" function...
Hi there, I am using sigma studio for sharc with version of 2.0.0.And everytime I enable the "Perfromance Monitor" in sigma studio,I find the application in CCES runs into the...
View ArticleADE7758 not used pin
Hello Please let me know about not used pin of ADE7758Our customer will use ADE7758.But he does not use ICP and ICN. (Another input pins are used).In that case, are ICP and ICN connected to GND ?...
View Article