Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Pulse amplifier

Without buying every gain block and ADC driver there is, I would like to know which amplifiers in the Gain blocks such as ADL5611 and ADA4960 will pass a 2 ns wide pulse without distortion.   That is,...

View Article


Re: Configurations for KC705 with FMCOMMS1 to run XCOMM example

Arul: Xilinx versions their boards "A", "B", "C", etc for pre-production boards. We can not support pre-production boards. There are too many changes, and too many bugs before the production "1",...

View Article


Re: ad6676 reference design

So can I repeat the question the adc core has two 32 bit outputs. Where is I and Q? Thanks

View Article

AD9524 i2c data line

On a i2c bus I have an AD9524  which is powered OFF when all the other devices on the i2c bus are ON.The pull-up resistors on the i2c bus are 3K.On the i2c clock line I measure 3.3V after power on but...

View Article

Re: AD6676 driver

Hi, After going through the schematic I realized that the FPGA should be fed by the 200MHz clk and so "fpga_selb" needs to be pulled high. I modified the reference design increasing the width of the...

View Article


Image may be NSFW.
Clik here to view.

Re: adv7393 Aptina MT9V024- Schematic review

Kind reminder.Thanks

View Article

Re: Low level control of AD9364 HDL/Muxes via IIO - info request

Hi Alejandro,Regarding the scan elements please see here:IIO device files [Analog Devices Wiki]Accessing registers directly please see...

View Article

Re: Question for your AD7891 ref output

Hi, Kaos. Let me check on this. I'll get back to you soon. Regards,Karen

View Article


Image may be NSFW.
Clik here to view.

the new design of ADI's site and my eyes

I don't like the new design of ADI's site.Now when I enter the product page my eyes be tired very quickly because color palette is badI think that soon I can hold abhorrence to the new design of ADI's...

View Article


Re: Use gpio to debug in ad9362

Hello, The button is already part of the design for FMCOMMS2. Is this the design you are talking about ?  If so, it is connected to the gpio from the PS7, specifically gpio [1].  Regards,Adrian

View Article

Using a balun for ADuCRF101

Is it possible to use a balun instead of the network of discrete components in the RF design? If so is there a recommended balun part?

View Article

Re: failed to boot kernel on zedboard with adv7511

Hi,I have met the same question in booting zedboard like you .The log messages say 'Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b',and I don't know what's wrong. Have you...

View Article

Re: "Resetting" AD9361 from software?

Should be fixed now with this commit:drivers/iio: Fix MODULE building · analogdevicesinc/linux@9a6fef6 · GitHub Thanks for pointing out. P.S. We always accept also patches  -Michael...

View Article


Re: Using a balun for ADuCRF101

Yes, basically you may use any possible antenna and matching network for the particular targeted frequency. Sorry we have not tested with a balun so far and cannot recommend one.

View Article

ADuCM36x Analog Input Channels

Hi sir,I have one doubt about the ADC single ended channel configuration in ADuCM361 controller.In that we have channels from AIN0-AIN11 then if we want to configure them in the single ended we will...

View Article


Image may be NSFW.
Clik here to view.

Re: ADuCM36x Analog Input Channels

In the way you describe it, yes you may be able to use 12 single ended inputs.But as in other threads already high-lighted, for the input specification and for best performance we recommend that all...

View Article

Re: ADP5023 - ADIsimPower Simulation Tool

Hi Hong, As I understand, the ADP5023ACPZ-2-R7 has the HIGH UVLO and can be used for 5V input only and not for 3.3V Input, is it?Is the ADP5023ACPZ-R2 has an ENABLE on LDO?Witch part number shall be...

View Article


Re: ADV7341 I2C

Hi Amnon, No, I don't believe there is. It is a fair point though and worth noting for any future generations. Regards,Paul

View Article

Re: bf533, linux and libusb

Also could you give more detailed description about the function you want to implement for your products over USB, so we can together work to figure out if there is another solution without libusb.

View Article

Re: ADCLK custom board design

Thanks for reply DSB, I've been away so couldn't see earlier. So I made my own custom board keeping all the trace lengths as short and equal as possible (lengths of CLK, CLK_BAR, 0, 0_BAR, 1,...

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>