Re: AS5645R I2C readback sequence?
Hi, Mark-san Thanks so much.I appreciate your response. Best regards,sss
View ArticleRe: [ADV7186] Input Capacitance of AIN
Hi TomY, The ADV7186 is still under NDA. So therefore we do not release any information to a public domain.Please,get in touch with your local FAE. Regards,Edwin
View ArticleClik here to view.
Re: AD8429 offset voltage
Hello Anna, I have replaced the AD8429 with the AD8421. It works fine. I dont get problems with the saturation. But their is one point, I need more informations. The maximum rating of the input...
View ArticleRe: AD1974 sample rate setting.
Hi, Dave Thib Thanks so much.I appreciate your response. Best regards,sss
View ArticleClik here to view.
Re: [ADV7186] Input Capacitance of AIN
Hi, GuenterL Thank you for your reply. I was forgetting this ADV7186 is NDA device.I'll contact to ADI directly.Best regards, TomY
View ArticleRe: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
Will this fmcomms card will be good enough for using for using it as a radio for freq range 225-400 MHz for good sensitive and good snr for real time or this board is only for evaluation purpose? And...
View ArticleHilbert transform for ADAU1452
Dear support team, I want to get a Hilbert transform for ADAU1452(like it for ADAU1401).Do you have a schedule of making it? If you don't have it,please tell me how to make it by standard modules,...
View ArticleCan AD8476 be used to drive ad7176-2(24-bit ,250ksps) adc?
I want to use AD8476 as a single ended to differential convereter. Converted differential signal will be read by using ad7176-2 which is 24 bit adc.AD8476 datasheet says that it is suited for driving...
View ArticleRe: Can't get ADUM4160 to work
MSCantrell, thank you very much for your response. It seems you are right. I connected an oscilloscope to this bench supply (no load) and the results are, well, pretty bad. There is a 7V transient...
View ArticleRe: Documentation init struct query
Oliver: http://www.analog.com/en/design-center/landing-pages/001/ad9361-ad9364-integ-rf-agile-transceiver-design-res.html --------- Guidelines for obtaining AD9361 and AD9364 technical support are as...
View Articlehow to write a letter to apply some books?
how to write a letter to apply some books,<你好 放大器>?
View ArticleRe: Documentation init struct query
Hi Robjn, How should I reproduce an the issue on the AD9361 evaluation platform if the signal which leads to this issues is generated from VHDL? Regards, Oliver
View ArticleRe: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
It depends on which board you have. please refer to:http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/introduction People use the exact setup in production designs. Others add external...
View ArticleClik here to view.
Re: Documentation init struct query
The ADI design can send out arbitrary files: http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/software/basic_iq_datafiles Can you create an representative waveform, and play it out to...
View ArticleRe: AD9912 driver not found / evalboard not connected
Hi,thanks it now finds the board.
View ArticleRe: AD9364 Baluns
We have not tested any baluns in that frequency range, so I can not recommend any specific ones. This is something you will need to determine yourself. - Robin
View ArticleRe: AD-FMCOMMS3-EZB power only
Jan: What are you trying to test/measure? If we understood what you are trying to do, we may be able to help give better guidance. - Robin
View ArticleRe: PVP Convolution Coef update bandwidth and delay
Thank you!You means the update of coefficient registers should always be faster than the data stream?For example, if I processing each small frame(5x5 pixels) with refres 5x5 coeffs in CONV block,will...
View Article