Re: Power consumption data for BF70x
Hi Joe, are there any new information about consumption data for BF70x? Is it planned to publish a calculation for BF70x that will be similar to the existing excel file for BF60x? Would it make sense...
View ArticleMEMS Gyroscope Acoustic Waves Rectification
Hi, Do you have any data for Acoustic Waves Rectification in MEMS Gyroscopes? I just would like to estimate acoustic wave impact on MEMS gyroscopes performance. Regards,Ivan
View ArticleRe: ADE7878 AVDD DVVD error
Hi Hmani,I got the ADE7878 working. I think the problem is with the ground connection. I got a new ADE7878 IC and dead bug soldered it on a prototype board. Now everything works fine. There was nothing...
View ArticleRe: Ref Design KC705 AD9364 Role of DDR3 cntrl and DMA
Hello Istvan, Thanks again.Means, I must design the new filter in order to adapt these frequencies?Is it not possible to use the default coefficients in order to run the modulator of BB 10MHz? Do you...
View Articlead vdsp preprocessor at asm
Hi guys, how can we detect inside the header file that now is a asm compile time. file crosscore.hxx:header:#ifdef ASM //what is the proper name of macros that is used to detect compiler...
View ArticleRe: [ADV8005] OSD fails to show on TV
Hi Joel Ding, The first four bytes values are the binary identifier value that we set it in project settings. The last four bytes will give the version Best Regards,Jeyasudha.M
View ArticleIs there any way to get email alerts when specific questions are posted on a...
Hi Support, I would like to get email alerts when particular questions are posted on a group. For sample, I can say that in video group, any discussions related to "OSD" are posted, is there way to...
View ArticleRe: AD5933 and AD5934 evaluation board software commands
Hey guys, I have been trying to open the labview code in labview 8 but it doesn't work. Can you plz guide me which labview version can be used?
View ArticleRe: Charc ADSP-21489 boot problem
In addition:Recorded in the flash swaping LDR file. After loading the kernel SPI activity is, apparently trying to read the data of the main program.Attach disasembler when connecting the emulator...
View ArticleCould ADV7403 support YPBPR/RGB 1080P30 component input?
Hi,We want to use ADV7403 to design a video system with YPbPr/RGB input.Could it support to 1080P30 analog component input? Another question is could ADV7393 support to 1080P30 output? We also want to...
View ArticleRe: Could ADV7403 support YPBPR/RGB 1080P30 component input?
Correct the Another question is could ADV7393 support to 1080P30 output? We also want to develop a product with this encoder. In datasheet, there's some description about standards supported. Does it...
View ArticleADSP-TS101 Booting Option
Dear Analog Devices Team, We are using ADSP-TS101SAB1Z000 in one of our design, We have made strap pin /BMS as "0" so that the system boots from EPROM/Flash immediately after reset. In the ADSP-TS101...
View ArticleRe: ADAV803 problems
Hello Dave The workaround seems to be a good solution but i wish to know if there is a better one. Signal is braking constantly and periodicaly. I am switching it on and off for a longer and longer...
View ArticleAD9467EBZ ref design
Hello, I hope these queries haven't been answered in some other thread (I tried searching for them but couldn't find any).1) The custom peripheral added to the AXI bus in XPS is axi_adc_1c_0. This...
View ArticleRe: Interfacing ADAU1701 with AD1955
Apologies for the bump. Does there need to be a level shifter from the ADAU1701's 3.3V to the AD1955's 5V when using this buffer? Does the supply voltage of the buffer matter here?
View ArticleRe: AD9915 parallel write timing
Thanks for the clarification. Regarding IO_UPDATE and SYNC_CLK: I understand that one can write in parallel mode multiple registers before doing the IO_UPDATE, so the IO_UPDATE timing does not have to...
View ArticleRe: ADAU1761 at non-audio sample rate (i.e. 51200)
Hello, Yes this is permissible. The data sheet allows for a MCLK period as short as 37 nS in 512 x fs mode. This corresponds to MCLK as high as 27 MHz, or a sample rate of 52.7 KHz. Thus,...
View ArticleADV7188
HelloI would like to ask on the above ADV7188 decoder.I think I see on its datasheet (Rev 0 from 2005) a contrediction between Table 9 and Table 101at the definition of INSEL[3:0] Register about values...
View ArticleRe: AD9364 External LO phase noise
Hello again, I measured the phase noise at the Tx output as you suggested, with internal and external Tx LO - in both cases the phase noise was ~-116dBc/Hz at 5-20MHz offsets (the test was done with Tx...
View Article