Re: OS for AD7194 Evaluation board
Hi Johnny, I have the same problem of Nom on my Laptop with Windows 8 64-bit. Could you send me the correct drivers for the USB interface?I tried the last version of the SW downloaded from the AD...
View ArticleRe: ADIS16480 Position tracking Problem
Yes, the 0,0,1g notation is what I would expect. However, it takes around 2-3 seconds to return to a 0,0,1 value after experiencing a movement... Interestingly this does not happen in body frame..
View ArticleClik here to view.
ADIS16251 vs. ADIS16265 Performance
Hi, According to the datasheet for the ADIS16251 rate sensor, the sensor has an angle random walk of 3.6 degrees/sqrt(hr), and the datasheet for what I'm told is one of its recommended replacements,...
View ArticleRe: ADV7625 OSD Text characters are not clear during emulation and...
Hi All Thank you . I known how to do .And the new test result is like as you show me the picture.But still have some characters can't display like "强" and so on.
View ArticleRe: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi Ram, Unfortunately I've still to hear back from our Hardware team regarding the expected voltage on TP18 and TP19. I've just pinged them on this issue and will let you know once I've heard back. It...
View ArticleRe: AD9361/4 BBPLL locking time & resolution
AD9361 AND AD9364 INTEGRATED RF AGILE TRANSCEIVER DESIGN RESOURCES | Analog Devices This is the link. Download requires registration.
View ArticleRe: The system is crashed, I can't set anything. And I click the tap on the...
Moved to Linux Software Drivers.
View ArticleRe: ADF7242
Questions on ISM and Licensed Band Transceivers (products with ADF7XXX part numbers) are no longer being handled on the EngineerZone and should be directed to your local sales organization
View ArticleRe: ADV7842 and registers “SPA_PORT_A”, “PORT_A_CHECKSUM”
Sorry for the delay. It is taking a while to review the documents with appropriate HW and SW engineers. -Matt
View ArticleClik here to view.
Re: H264_BPEncoder for CCES
Hi Raj, Shame the demo doesn't build though! I purchased an ADZS-BF609-EZBRD BF609 evaluation board, ADZS-DECODE-EX3 Video decoder module, and downloaded BSP for each. I downloaded CCES 1.10 and H.264...
View ArticleRe: Can I transmit static signal via ADuM7640?
Hi everyone, In my case also same to the above one & I am planning to use ADUM7643 in my application where it will be used to receive & re transmits the 500Hz periodic pulses from the filed...
View ArticleRe: musb with EZBRD in full DMA (from kernel 3.7 on)
Hi Scott, I know, I've independently started work on bringing our board over to the latest analog devices release kernel. That's what I'm working on. However, I find that on the BF526 I get the same...
View ArticleRe: please help me about setup on ad9914
Hi happywarwick I can offer some suggestions to get you started. 1. In order to use the internal PLL correctly, you must do a VCO cal on startup, followed by a DAC cal. Do this after your master reset....
View ArticleRe installing VDSP++5.0 windows 7 64 bit
Hi , I was trying to reinstall VDSP++ 5.0 Update 10.1 on Windows 7 64 bit . After starting the VisualDSP++5.0.exe i get 1.Reapply existing install2.Install a new instance of this application into a...
View ArticleRe: AD5752 SPI Issue
Hi! Thanks for your prompt response. Unfortunatelly I am not allowed to provide the schematic... Anyway, the SYNC signal is not shared at all, it is just wired from the uC to the DAC. Actually every...
View ArticleRe: Not correct output amperage of EVAL-AD5421SDZ
Hi Mark! Thank you for your reply. I think that if it's not works in 4 - 20 mA, than it works not right, and it's not good..Unfortunatly I can't use FAULT pin. Maybe the problem is in the not connected...
View ArticleRe: Spurious noise on ADF4159 PLL
Thanks rbrennan for your explanation, I think to change for ADF5355 for its higher frequency than ADF4155.But, has it the same architecture like ADF4155 (without wandering spurs) ?
View ArticleRe: BF516: gnICE JTAG 3.10 Kernel debug symbol mismatch using gdb/gdbproxy
This question is actually about how to debug linux kernel using gdbproxy. This question will be better answered by the Linux Kernel people.
View ArticleADL5390 Minimum Operating Frequency?
Hi...Just wondering if anyone knew if the ADL5390 could be used any lower than the 20 MHz specified in the datasheet. I saw another product reference that specified 10 MHz as the lowest frequency for...
View ArticleClik here to view.
AD9361 init. Compare 2 logs, my and demo projects...
Hello, I wrotecode to initialize the AD9361 by SPI controller. My log is very similar to demo project log (i write all register values my and demo projects in the files and compared them). But after...
View Article