Clik here to view.
Re: Run just an .dxe file when in CCES
Needed to follow up at the start of a new term and a new set of students1) Students are unfamiliar with CCES 1.0.3 and I want to run a simple .dxe2) Tell students to build an "empty" project3) Add the...
View ArticleClik here to view.
Re: Run just an .dxe file when in CCES
Found a way -- delete the System directory in the empty project.Right click on executable in Debug directory -- say Debug asBuild occurs -- CCES says nothing to makeCCES loads old executable that was...
View ArticleClik here to view.
ADP230X - Max operating voltage
Hello,keeping in mind the application of the ADP230X, in a non inverting configuration, to obatin -14.5 V from a +5 V power supply, the maximum operating voltage of 20 V is closer near and considering...
View ArticleRe: OP4177 opamp is not working as voltage limiter.
Hello Harry!I selected OP4177 as a replacement for LM148 in my design based on the specs given in datasheet. I found it better in every aspect e.g. offset, bias current, supply current. Slew rate ,...
View ArticlePowering DDS AD9852 Evaluation Board ???
Hello,In DDS AD9852 Datasheet it is mentioned that in order to power up evaluation board;3.3V Vcc, 3.3V DVDD and 3.3V AVDD are required with a common ground. On Analog Devices website it is also...
View ArticleRe: Printing data from adc_capture ?
Hi, I have got problem with data from adc_capture(). I print samples from adc_capture() to console but when I set number of samples grater than 0x1FFFF I read random value from address in DDR for all...
View ArticleRe: AD7949 SDO error
Hi, yk.Do you see this problem on multiple parts? Are you using the AD7949 evaluation board? Which mode are you trying to use RDC/RAC/RSC with or without busy indicator? Note that there is always a one...
View ArticleRe: ADXL363 breakout board
Neil, Thanks very much for the information. As a small business, however, (getting a $150 eval board and replace the part) or (creating one from scratch from its schematic and add the ADC part) is out...
View ArticleClik here to view.
Re: A very URGENT question about AD9915
Thx for the reply, As i understand, DDS' SFDR can not be found & measured by observing the spuriouses with spectrum analyzer while you are changing the amplitude of the output.You are using another...
View ArticleProblem with output signal of ADXRS642
Hello!We have some ADXRS642 gyroscopes. Output signal (RATEOUT) have additional squarewave about 0.5 - 1.5 Volts (without external capacitor between RATEOUT and SUMJ, Fig. 1, Fig. 2) and about 10 mV...
View ArticleRe: ADL5304 usable range
Hi Peter, Like i mentioned in the other post, it really depends on the customer's error requirements. If you have a limited operational temperature range (0 to 50 degrees C) and can accept 1-2 dB of...
View ArticleRe: Why ADSPCM403‘s SPI0_SEL3 pin always 'high'???
ADI supplies drivers for the SPI. Also there are board support files for the processor included with the download.
View ArticleRe: ADXL345 characterization data at 3.3V power supply is available?
Hi Jane, This information can be found in the datasheet. Please refer to the "Typical Performance Characteristics" for histograms at 3.3V supply and behaviour over temperature. Information is also...
View ArticleRe: Any Touch/pressure sensor from Analog?
Sorry we don't offer tactile touch or pressure transducers. We do have CapTouch products that maybe suitable. Details can be found here:...
View ArticleTDD operation documents
Is there any document about TDD operation for AD936X? Or any app notes?
View ArticleUsing external clock on ADXL362 EVB
Hi, I am using ADXL362 EVB (Real Time Eval System for Digital Output Sensor | Analog Devices) to evaluate the ADXL362 accelerometer. I am wondering if there is a way to set the EVB to run on external...
View ArticleRe: TDD operation documents
The documentation that is available is the datasheet and the two reference manuals. The reference manuals go into quite a bit of detail on TDD operation in different sections.
View ArticleRe: ADF4360-7 power down mode
Hello Taiki,Because MUXOUT was programmed to o/p digitla lock detect before power down, we would expect that MUXOUT would go low when the device was powered down via CE, and stay low. regards,Brigid.
View ArticleClik here to view.
ADV8003 TMDS Receiver Video Detection
Is there any way to determine the resolution and frame rate into the ADV8003 TMDS input if it is being fed DVI and not HDMI? HDMI supports AVI Info-frames which the ADV8003 can capture to be accessed...
View Article