Re: Calibrating IRMS of ADE7758
Oh, Thanks GOD. Finally I got good readings.I have used 10ohm resister in between AVDD & DVDD. I just short circuit the two pins and now I can get good readings. Thanks dlath, I saw your suggestion...
View ArticleRe: Data clock from AD9361 FMC card in DDR mode
I just added a note to: http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/introduction That should answer your question. - Robin
View ArticleHigh voltage digital potentiometer
Hello, I'm looking for a digital potentiometer that has an analog rail that can handle a voltage of 60V.Does such a thing exist? if so then where can I find it? Thanks much!omer
View ArticleRe: ADV7280 Script writes to a read-only register.
Hi All,The write to register 0x13 is deliberate. User Map register 0x13 contains a read only register (Status 3) and a write only register. The write only register controls whether voltage is output to...
View ArticleRe: Communication system toolbox hardware support package for xilinx zynq...
Hi Shobi, If you would like to implement the QPSK Transmitter and Receiver, you should run Tx on one machine, and Rx on the other machine at the same time. To get started with, I suggest you to first...
View ArticleClik here to view.
Dynamic loudness in 1701
Hi, I am looking for a way to apply dynamic loudness to my signal in ADAU1701. I have found the dynamic bass boost block but that only adds gain to the lower frequencies. I want to add a dynamic...
View ArticleRe: ADE7758 LCYCMODE IRQ PROBLEM
Hi Harry077 Yes. The value 0xF7 in address 0x7D makes sense. Try writing 0x8F7 to that register value and see if the waveform samples are easier to read. Do you have multiple ICs? Do you see this...
View ArticleRe: using AD8067 as inverting amplifier
Thanks JinoL. I am sorry to be very late to say thanks.
View ArticleClik here to view.
Re: Dynamic loudness in 1701
Hello Markus, The attached circuit may fill your needs. It takes advantage of a recent addition to the ADAU1701's toolbox, the log-spaced lookup table. This greatly simplifies dynamic...
View ArticleRe: code of the test pattern of AD7960?
Hi Maithil,May I ask you for the test patterns of AD7960? Thanks,Majid.
View ArticleADV7511 Audio FIFO Full interrupt
Hello. Audio FIFO Full interrupt(0x96[4]) of ADV7511 occurs in rare cases.Would you please enumerate the reasons to cause Audio FIFO Full?In other words, where and what should we check? Your advice...
View Articlefmcomms2 with FDD ENABLE/TXNRX Pin control
Hi I am using fmcomms2 and zc702 with NO-OS driver.I want to using the FDD ENABLE/TXNRX Pin control mode .I change the ensm_enable_txnrx_control_enable to 1 and the enable to 1.But the TX can't get...
View ArticleClik here to view.
Re: ADE7758 | Issue reading WFORM register
Hi hmani, unfortunately this behavior isn't intermittent: When I set the MASK bit for WFSM to 0 manually or by performing a software reset, the status bit for WFSM won't change from 0 to 1 and the...
View ArticleBug in SHARC USB EZ-Extender software?!?!
Hi, I'm playing around with the USB Audio example software. It seem sot work in Full-Speed-Mode. Mac OSX recognizes the new audio device. Now I'm changing it to High-Speed-Mode and USB Audio Class 2.0....
View ArticleAD5933 EB interface - need to extend
Hello! We have bought AD5933 EB to use it to analyse electrical circuits in our products.The graphic user interface is very friendly, but we need to extend it a little and to add a simple data analyzes...
View ArticleClik here to view.
Re: Read input value (like GPIO) for ADSP-21469 from simle C code, is it...
You can read the status of external pins through the FLAG register.You need to make sure that they are configured as inputs.The dedicated FLAG pins can be read directly.You can also read any DPI pin...
View ArticleRe: Data clock from AD9361 FMC card in DDR mode
Tomas: If the spec on page 6 of the dataseet (DIGITAL DATA TIMING (CMOS), VDD_INTERFACE = 1.8 V / Capacitive Load) is max (like you state) - it should be over a column. What is in the datasheet is...
View ArticleRe: ADE7953 for DC metering
HI Dlath, What should be the LINECYC value in half line cycles for accumulation time calculation for DC. Thanks
View ArticleRe: Artix AC701,ADV7511, HDMI,synchronization errors on the image resolution...
Serg: Just wanted to check -- the monitor supports 1920 x 1080 progressive? -Robin
View Articlefrequency response with AD5933
So when looking into a certain type of sensor, I read that this chip could be used to send an impulse frequency (in the MHz range) and switch over to read the impulse response frequency via an antenna....
View Article