Re: 0xEC96[4] register of ADV8005
Hi Kika, Yes it is Audio FIFO Full. Best Regards,Jeyasudha.M
View ArticleRe: AD9363 maybe quality problem
Can you please post the results of XRAY testing and how AD9361 is performing in your hardware?
View ArticleRe: ADV7401 video drifting. Rising GND reference?
Do you have PRIM_MODE and VID_STD set to an appropriate value? Is the back porch clamp clamping in the wrong place?
View ArticleRe: ADV7401 video drifting. Rising GND reference?
Hi Guenter, That is what we see, but for some reason the chip seems unable to float our signal at this level, so we have to help it. It is as if it's biasing circuit is not strong enough. The AC...
View ArticleRe: HMC1099LP5DE-ADS simulation
The HMC1099LP5DE is still in the pre-release life cycle so we don't have s-parameter mode files for this device at this time. We will provide this information shortly when the product is released. You...
View ArticleClik here to view.
Re: HMC-C018
I have checked with Engineering. Please verify your logic levels are per the data sheet. In addition, try the example in the data sheet for a 0.5 dB attenuation state. Best regards,Mikecs
View ArticleRe: ADE7753 Waveform problem - LSB is 0x00 when HPF is OFF
Hi Dlath Thanks for your reply. I’m not sure that I understand, what did you mean. Can you explain more detailed? In my case (I measure 5V USB via PICkit by resistor divider 1:76, the signal is some...
View ArticleRe: ADE7753 Waveform problem - LSB is 0x00 when HPF is OFF
And main question: How can I measure dc with 24 bit resolution?
View ArticleRe: AD8421 output voltage without input
Thanks for the picture.A 10MHz amplifier on a bread-board? The poor thing. Probably shock itself to death, oscillating like crazy.See the data sheet, section about grounding:"Power Supplies and...
View ArticleRe: AD8421 output voltage without input
thanks for your answers. Some comments in advance for your upcoming tests with the new device: 1) even if the connection of Ref made no difference in your previous tests, Ref must be connected to GND...
View Articlescript file for adv7513
sir/madam,Do you have any script file for ADV7513...?? if yes please inform me...
View Articlediscontinuation
hi , considering discontinuation of some of your products, for some products there is not any replacement.some like hmc890lp5e, hmc892lp5e, hmc895lp4e, hmc896lp4e. is there any planned program to...
View ArticleRe: Clock AD1937
Hello Andre, Glad your up and running. The error you did is easy to do. Shortly after we published this datasheet we started putting in pictures of the bitfields and that helps so much. Let me know if...
View ArticleRe: Question about file write on Sharc DSP
Hello Wei Jl I am the applications engineer for the AD1939 but I am not super familiar with the DSP tools side of your project. So I would like to make sure the DAC is actually getting what it needs to...
View ArticleCN0269 labview source code
I'm using CN0269 with SPD-B. I want to customize the aquisition using labview programming. Any reference source code in labview is avaiable?Thank you!
View ArticleClik here to view.
CN0269 with SDP-B labview source
I'm using CN0269 with SPD-B. I want to customize the aquisition using labview programming. Any reference source code in labview is avaiable?Thank you!
View ArticleIEEE802.11ac 160 MHz BW
The IEEE802.11ac specification allows instantaneous bandwidths up to 160 MHz. What Wideband RF Transceivers are available for this? If there are none, what is the highest level of integration...
View ArticleRe: Using custom hdl design
Like I said - it depends what you did. Since you didn't describe what you did - it's just wild guesses if things will still work or not. As long as the ABI is the same, it should be fine. - Robin
View ArticleADV7181D pixel output during power up
Hello, I'd like to confirm what is pixel output status during ADV7181D powering up.As attached is power on sequence (not from ADV7181D d/s but suppose ADV7181D has the similar power on sequency), what...
View ArticleRe: fmcomms1 adc_capture and printing adc values
Thank MiT for your reply, Yes, they look exactly like that.But the thing that bothers me that I and Q keeps interchanging. And sometimes I get both I and Q same as any one of the LUTs. Please have a...
View Article