Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

HDMI convert CVBS

HI,everybody. Now  i  have a question to you that  is there  any  IC can convert HDMI video data to PAL output(extract  may  allow )!  such  as  i use ADV7611  to  receive HDMI source video data ,then...

View Article


Image may be NSFW.
Clik here to view.

Re: Two tone sample on dma_setup or dds_setup for FMCOMMS1

Thank you Dragos,I'm successful display the two tone spectrum by setting desire f1 and f2.Now its clear for me on dds_setup function. Then I use dac_dma_setup by default code in test.c and observe the...

View Article


Re: AD8367 - Maximum Output P1dB Point in 50Ohm configuration

I haven't looked at all of the S-parameters that you provided for the AD8367, but looking at S22 for Vgain = 2, 5, and 9 volts at about 25MHz, it appear that the output impedance is about 13 ohms. The...

View Article

Re: AD8367 - Maximum Output P1dB Point in 50Ohm configuration

Hi Sugumar, I suggest that you convert S22 for the AD8367 to an output impedance and see what you get. When I convert S22 to an output impedance I get about 13 ohms, which seems what one would expect...

View Article

adau1452 avc block adjust freeze level and max. gain

How can I adjust the AVC block adau1452 with higher values for freeze level and gain level? The values that I can be set too low for me and I want to have a greater range avc.  Or, there is also...

View Article


Image may be NSFW.
Clik here to view.

Re: Using custom hdl design

Hey Robin,  Probably in wasn't clear enough. Because I think you misunderstood me. So I'll try to explain again.  I have downloaded the hdl from github and did like this guide...

View Article

Re: ADV7610 480p Color Issue

Here is my Device Manager screen after the EVAL-ADV7611EBZ is connected:

View Article

Re: Fastest PLL settling time - ADF4351 on FMCOMMS1

On the ADF4351, by bypassing the band select process, the fastest settling times you can achieve is in the 10s of microseconds. More info in the ADF4351 cheat sheet: https://ez.analog.com/message/156447

View Article


Re: IEEE802.11ac 160 MHz BW

Take a look at our Integrated Transceivers, Transmitters & Receivers section on Analog.com. http://www.analog.com> Products > RF & Microwave > Integrated Transceivers, Transmitters...

View Article


HMC439

Hello, On page 6-97 of the HMC439QS16G data sheet there is a graph at the lower right, that shows phase noise data for operation of SSB Phase Noise Performance, Pin= 0 dBm, Fin= 100 MHz. The data vs....

View Article

ADP5071 EVB Board Gerber

Dear All:I need to reference ADP5071 EVB Board PCB Layout design, can give me ADP5071 EVB Board Gerber File reference? thanks~  Best Regards,Cuttlefish 

View Article

Re: ADE7758 LCYCMODE IRQ PROBLEM

Hi Hmani, 1. Actually I tried reading Active Power with phase A, Irms and Vrms. Everytime I read I get cero in the WFORM register(just using a loop). Then I tried to wait until the /IRQ signal was...

View Article

Re: Fastest PLL settling time - ADF4351 on FMCOMMS1

Thanks for the quick reply. 1. However the RFout does NOT wait for the PLL to be locked isn't that right? The lock loop detect is for user to be able to poll lock status, no?2. Is there anyway to...

View Article


Re: FFT in BF506

Hello Prashant,I modified your original code with the info you gave to enable the 2D mode. I modified the function Init_Sport() with the following: *pDMA4_CONFIG = FLOW_SMALL | NDSIZE_4 | SYNC | DMA2D...

View Article

Re: How to interface ADV7513 to WUXGA?

The same set up for UXGA should work fine for WUXGA

View Article


Image may be NSFW.
Clik here to view.

Re: ADCLK925 Max. V_IH

Hi Paul, When I posted my last reply it only showed "Thanks pkern" rather than the rest of my followup question. I went back and added the followup question regarding differences in datasheet...

View Article

Re: ADV7612 and ADV7619 device ID

Not explicitly. I would look for any differences in the register maps you can use to do the identify since you know it's either one or the other, right?

View Article


Re: Equalizer setting for ADV7842

Other then the registers listed in the software users guide there are no other registers available.

View Article

FMCADC2 FFT Visualization in Oscilloscope Problem

Hi,I am currently using the FMCADC2 evaluation board with the AD9625. I'm using the Virtex 7 evaluation board VC707 and the oscilloscope application running on Windows and Linux systems. I'm actually...

View Article

AD9361 Linux kernel compatible with 3.14.0?

We need to add AD9361 device driver support and iio driver support the Linux kernel using by following the instructions in this...

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>