Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Looking for component advice

Hi, looking for advice.  Going to design three different signal conditioning circuits:-Thermistor interface (likely 10k thermistor)-RTD interface (PT100)-Strain gage interface (w/10V excitation) Will...

View Article


Re: AD9361 timing parameters

I did look at Figure 81 of UG-570, the figure is not very clear on how to interpret the timing numbers - hence the above question. If the data bits come out at the same time , are the min and max...

View Article


Re: Looking for component advice

Arnold,   Now days, a lot of customers just use an AD7793 for all three.  See fig 7 or fig 20 on the rev B datasheet. Harry

View Article

Re: Looking for component advice

Yep, I would but the ADC is already defined and I will be simply providing the interface between sensors and someone else's ADC.  Wish I could do the ADC also - it would actually be simpler!

View Article

Image may be NSFW.
Clik here to view.

Re: Op amp and Eval Borad Question

If you need high performance, the ADA4528 may work.  There is a universal eval board EVAL-OPAMP I believe.  Price for the op amp is reasonable for smaller projects...

View Article


Re: HSC-ADC-EVALEZ+AD9656 Matlab control

Hi Said, I think you may have limited the visibility for this post.  Can you add @msink so that he can see this post?   Regards, Jonathan

View Article

Re: AD9361 Filter Parameters

Hi Ralf, If I understand your question correctly, you want to change the FIR filter on AD9361 while you are using the chip (transmitting or receiving for example). One thing you can consider is to use...

View Article

Re: ADV7401 PAL input on VGA?

Thanks Dave, Basically I'm stuck feeding a VGA/RGB signal (from a converter that outputs VGA) to the 7401 on the VGA input (AIN1-3) as I am restricted by hardware...  End goal is to have this 7401 chip...

View Article


ADE5169 Apparent energy Measurement

Hi, I am using ADE5169 for Active and Apparent energy measurement. Active energy is accumulated using CF1 interrupt and Apparent energy using CF2(The necessary configurations are already done). The...

View Article


libiio tx channel disable

Hello, I have a matlab script (attached) to generate iq data files for a single tx channel of the fmcomms3 for a CW tone at a given frequency offset.  The output spectrum shows the main frequency...

View Article

Re: ADV7280

Hi Guenterfirst thank you for your help.I checked and rechecked my design, swapped the I2C line and back, but no answer.one thing I need an answer to. the devices from DigiKey do not carry the Analog...

View Article

Re: ADAU 1451 slave i2c port trouble

Thanks for the information.  I will compare your schematic to mine, but a cursory view tells me I have it all hooked up correctly.  I am going to try another board in case I just have a bad DSP chip on...

View Article

Re: ADV7280

Yes, that could be a problem.  All our parts should have clear identification.  Can you attach a picture of the part so we can read what is printed on the part?

View Article


Datasheet difference of AD9978 and AD9978A

Hi all I have questions about datasheet difference of AD9978 and AD9978A.  (1) update timingI thought the AD9978 and the AD9978A same specification, but there is a difference in the  update timing of...

View Article

Image may be NSFW.
Clik here to view.

Re: Op amp and Eval Borad Question

Thank you for your reply. I have just realized that since my signal is -5V-0V, I would probably need a V supply of (-12V)-(2V). I did not see any V supplies with negative voltage input. Would you...

View Article


Image may be NSFW.
Clik here to view.

Visual DSP++ drops Build Window, can't restore, MAJOR BUG!!

During a debug session using Visual DSP++ 5.1.2 with a BF547M,  I was unable to halt the processor so I powered down the JTAG.   The goal was to try to read the debug window.   Disconnecting the...

View Article

Re: ADV7619+ADV8005 hardware validation?

Hi,  which version of the software package you currently have? Regards,Dominic

View Article


Image may be NSFW.
Clik here to view.

Re: AD9361 parameters

View Article

Re: adv8005 without BF524

The EVAL-ADV8005-SMZ should have come programmed with a software driver which will route DVI/HDMI signal from JT11 to JT4. Source is connected to JT11. Sink is connected to JT4. All you need to do is...

View Article

Re: ADV7619+ADV8005 hardware validation?

We were given VSP 1.81RC1

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>