Clik here to view.
Re: AD9915 output attenuation when driving FPGA. Explanation and solutions?
HI Lionel, Have you tried connecting at J9 without probing it. We're suspecting that it has something to do with your setup or the quality of cables that you are using. Checking at the last picture,...
View ArticleModifying debug_nets.ltx file
Can i change the code inside debug_nets.ltx so that make the Vivado H/W manager load the Probe datas and bind them into virtual bus automatically?and if yes, how?
View ArticleMatlab 2012 register with Visual dsp++
Hi sir I want to register or integrate with matlab 2012 toVisual DSP++ 5.0 version.Is Possible,Because whenever I command adivdspsetup on matlab command window the path appear and I click Ok but...
View ArticleClik here to view.
Re: BF609: second wake-up issue with hibernate mode
Hi Hammed, sorry for replying late, we have put lots of effort on this issue, and have had lots of internal discussions with world wide processor support team and other AE/FAE forces, no solid...
View ArticleRe: How to keep the SD of AD-FMCOMMS3 stay up to date?The wiki page is not...
Dear Cherif, When I failed to write the relative image into a new SD card, I formated the SD.Finally I finished preparing the SD card. I suggest you follow Drago's advice. Besides, one of my...
View ArticleRe: 1080p to 480p(16:9) using ADV8003 scaler
The register of 0xE828[4] is only for VOM.When i changed the VIM crop and PVSP_VIM_CROP_ENABLE(0xE883[6]),the image was anamorphic about 80 milliseconds.When i disabled PVSP_VIM_CROP_ENABLE and others...
View ArticleRe: AD7608 serial read trouble
Hi Marekm, The AD7608 clocks out bits on the SCLK rising edge, but the MSB is clocked out from the CS falling edge. If the first clock edge after the CS falling edge is rising edge then the AD7608...
View ArticleRe: Control of Boston engineering FlexMC kit with ADI CM408F
Thanks, If you can send me your email , I can send my simulink algorithm which I want to realize with the CM408F and the FlexMC kit. In that way you will understand my objective.
View ArticleRe: jitter be found at AD9880 output Hsync pin
Hi, Joe,thanks, I'll ask customer to verify your configuration. and get their feedback ASAP.
View ArticleRe: jitter be found at AD9880 output Hsync pin
Hi, Dave,if the bigger jitter is expected behavior, it means it must have a retiming block between AD9880 and SiI9136, right?
View ArticleClik here to view.
What was wrong with my boot process of Ubuntu system supporting the AD9361...
Dear all, Here is the boot record picture I took just now. DragosB I wonder whether the same driver should be boot for twice, where the first action was OK but the second failed.In addition, the upper...
View ArticleRe: [ADV7282-M] 0x04 "Extended output control" register.
Hello, Thank you for your reply. I talked to the customer and I negotiated him to wait for the answers next week.He said it's ok. By the way, following questions are from him,...
View ArticleHow to observe the FM band with an AD9361 FM-COMMS3-EBZ board?
Dear all,I was trying to listen an FM program according to the instructions on http://wiki.analog.com/resources/tools-software/fm-radio.But I couldn't finish the following operation. The system...
View ArticleClik here to view.
Re: ADV212 with 576p @ 25Hz
Hi Dave, Thanks very much for the reply. Pixel Start of 1 and COD_STYLE 0x02 are both noted, and we'll change our register settings to reflect that. That was also useful info. on the syncs and frame...
View Articlehow to enable the IwIP stack in ADSP BF 527 via Cross core embedded studio or...
Hi, I am Dinesh Anton Raja, I am using ADSP BF-527 board to develop the video processing applications, I need to connect the ADSP BF-527 to the ROUTER. Then I am using Cross core embedded studio 1.0.1...
View ArticleRe: How does the ADG2128 have such small input capacitances
Hello Tom,The off capacitance of each ADG2128 switch input is 11pF. When the switch is off it is not connected to any other outputs.Regards,Stephen
View ArticleRe: adv7282-M display issue
Hi The problem is stillnotresolved when resetting the chip.I think itneeds toprocess onplatform side.Could you tell me how to detect a new input with the INTRQ pin? How to set the related...
View ArticleRe: ADAS1000 amplitude overflow
Hi Sebastian, Digital lead mode is expressed in two's compliment while analog lead mode and electrode modes are not. THis can cause confusion at times but this does not appear to be the issue here.What...
View ArticleADV7619 CEC and HPD
Hi, I will be using an ADV7619 with a hdmi connector on one of the inputs for general use.This makes it very important for me to complie with the hdmi 1.4 standard. Do I need any pull up or down...
View ArticleRe: Customizing ADI's AXI DMA Controller in ZC-706 with FMCOMMS4 board
Hi, Customizing the core should not be a problem. The error looks like the core was deleted or some of the files were not regenerated properly. Btw. it is also possible to turn of the cyclic mode at...
View Article