Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: How to verify digital loopback in AD9364?

Hello Dragos, Thank you.But I had already gone through that link before posting the query. I believe that API does the digital loopback, but how exactly can I validate it manually? I mean I would like...

View Article


About HMC6981LS6

About the detect circuit of HMC6981LS6(page 9, datasheet), How much tolerance of resister we should select?

View Article


Re: ADV7625 TXB video flash when unplug TXA cable

Hi Jeyasudha, We tested with three different of SONY "4k2k" BD-players.  Steven

View Article

Image may be NSFW.
Clik here to view.

Re: AD630 Unity gain error?

Gerry,   you have exceeded the input common mode voltage range on the comparator.  Try +/-1 Volt.How low is "low impedance source"?? Harry

View Article

Re: Analog tools integration support

Hi Dennis,Thank you for your inquiry. You have asked your question in the general help space for EngineerZone. I am moving your question to the FPGA Reference Designs area for assistance.Regards,Lisa

View Article


Re: ADM6713 Absolute Maximum Ratings Question

I’ve checked on this and the abs max ratings on these datasheet are not “tested”. They come from the process parameters used for these parts. The 25degC test condition is not appropriate. The abs max...

View Article

Re: ADAU1701 noisy sine waves

ADAU1701 full-scale output is 2.5Vpp, so 100mV is -29dBFS.  With dynamic range of 104dB, that still leaves 75dB signal to noise, or 13 bit.  Thus, quantization should not be the source of the noise...

View Article

FMCOMMS1-EZ I2C read operation

Hi, I am trying to use the FMCOMMS1-EZ board connected to a Kintex KC705 FPGA board with a custom hw build (.bit file) and custom from-scratch software (.elf file). I know that AD doesn't support...

View Article


Re: Op Amp for Low Current (< 100 mA) Measurement

James,   Instead of an op amp, I would use an InAmp.  And in the past five years, we have made specializedIn Amps for motion control.  Take a look at the AD8218. Harry

View Article


Image may be NSFW.
Clik here to view.

Re: ADAU1701 noisy sine waves

     Hi Jon,      I also believe that the reconstruction filter is necessary.  The top scope trace is after the eval board's filter (at its output mini jack), the second one below is directly from the...

View Article

AD9915 output attenuation when driving FPGA. Explanation and solutions?

Customer Question: We are using a AD9915/PCBZ in combination with a Xilinx ZC702 eval board.  We are using a Xilinx FMC XM105 debug board to access the clock and I/O pins on the FPGA.  The sync clock...

View Article

Re: AD5421 Offset Register

Hi BobR, How are you writing to the part? By that I mean the sequence of the commands that you are sending to the part. Would you be able to do the following in sequence?Do a software resetSet the...

View Article

Re: edit hardwareconfiguration in graphical sigma studio?

      Hello hubijo,     Now I understand what you wish to do -- change the Master/Slave bit under control of the running DSP program (graphical signal flow).  This would allow a self-booting ADAU1701...

View Article


Image may be NSFW.
Clik here to view.

Re: Register setting of ADV7513

Could you please teach about the above questions?

View Article

Re: SigmaStudio Automatic Speaker EQ Usage

Thank you for your question. Someone from DaveThib's team will respond to your inquiry shortly. Regards, Lisa

View Article


Re: ADAU1761 with ground-centered headphone configuration

Thank you for your question. Someone from DaveThib's team will respond to your inquiry shortly. Regards, Lisa

View Article

Re: Automatic Room Correction/Tuning using SigmaDSP or ADAU1452?

Thank you for your question. Someone from DaveThib's team will respond to your inquiry shortly. Regards, Lisa

View Article


Re: ADAU1961 pseudo differential input

Thank you for your question. Someone from DaveThib's team will respond to your inquiry shortly. Regards, Lisa

View Article

Re: SSM3302

Thank you for your question. Someone from DaveThib's team will respond to your inquiry shortly. Regards, Lisa

View Article

Re: The settling time of switching from CDS mode to SHA mode.

Hello , I'm sorry, I had a mistake."AD9982" is wrong and the question is about "AD9822". Could you tell me advice ? Thank you,ysuuzki

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>