Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: ADIS16209 Accuracy Problems and Assembly issues

Dear Mark,We have tested the values of the registers you had asked for:We got 0x3F51 in PROD_IDI and we got 0 and 0 in 0x1C and 0x1E. We are in a time pressing situation and we are no closer of...

View Article


Re: trouble compiling with Blimp ADV7625 OSD IDE and Emulator

Hi Ron, We will look in to the problem by checking all the steps that you have given. Please let us know what is the Blimp version that you have been using. Best Regards,Jeyasudha.M

View Article


[ADV7611] ABSOLUTE MAXIMUM RATINGS of "SCL/SDA Data Pins to DVDDIO" on...

Hello,I have a question about ABSOLUTE MAXIMUM RATINGS of ADV7611.There is a following description about ABSOLUTE MAXIMUM RATINGS of "SCL/SDA Data Pins to DVDDIO" on datasheet...

View Article

Re: BF607 SMC Timing

Hi, Could you please confirm how you are measuring the AMS time? I believe you are doing so by probing the signals, and capturing on the oscilloscope. Could you please share the respective screenshot...

View Article

AD9361 RX capture file save

Hi I am working with AD9361 FMCOMMs2 Zed board. I faced several issues need to resolved. 1. The ADI IIO oscilloscope gets hanged several times while working with it.  2. While validating RX performance...

View Article


ADSP-CM403

What are differents between ADSP-CM403FBSWZENG with ADSP-CM403BSWZ-CF/EF/FF?

View Article

Re: SSM2603 doesn't work at low temp

Hello Dave.At first thanks a lot for your work.But one thing.You are right that SDA and SCL have almost same layout.But BF533 GPIO pin doesn't work same for both SDA ans SCL.Let me explain why.SCL line...

View Article

Image may be NSFW.
Clik here to view.

Re: Packing String Literals

You can store character for a string in 16-bit memory area.

View Article


ADV7393 VESA format

Hello, We would like to input VESA format signal (VGA< SVGA< XGA)  to ADV7393 but datasheet does not describe VESA format. Question  Please let me know if ADV7393 supports VESA format.  If not...

View Article


Re: ADAU1701 and Arduino

Dear matse,  Welcome! I suggest you go Bob's first plan to go with the arduino writing changes to DSP's parameter RAM via I2C, since this will give u unlimited control in the long run. as a detailed...

View Article

What is the Technique of PulSAR?

Can anyony explain the different between ADI PulSAR and conventional SAR ADCs? Are they the same or anything special? Thanks a lot.

View Article

EN pin/Output pin of ADG5433

Hi Please let me ask 2 questions about EN pin/Output pin of ADG5433.Can I think EN pin output gets High-Impedance when EN pin is set High ?And during disabling output, should output pin be under max...

View Article

Re: ADE7816 change of direction interrupt timing

1. When you say 6266W is the full scale power level, do you mean that you apply +500mV to both current and voltage channel inputs of the IC at that point? Yes.  At a Vrms of 295V V will be swinging +/-...

View Article


Re: ADE 7758: Measurement of kW-hr

Hi hmani,After you explained, I understood a little bit of the line accumulation mode. But I have some doubts. The datasheet (pg 61) says that the LINECYC register sets the number of half-line cycles...

View Article

Re: Recommend Opamp for integrator in audio oscillator

Hi Mark, Yes I agree,selection of op amp is not easy. You should be able to identify which parameters your application should be of most interest.It could be the noise, precision or the cost for...

View Article


ADV8003 Horizontal Filter for Scaler

Hi, We assume that a FIR filter is used for the horizontal scaling filter.Can we have the following matters? 1) The Number of the taps for the horizontal scaling filter.2) Can we change the...

View Article

Re: Using the ADuCM350 to monitor the impedance of multiple channels

You're welcome, any time! ¬EM

View Article


Image may be NSFW.
Clik here to view.

Re: AD8495

Hi Stefano, Thanks for using ADI product in your design. I think you can use AD8495 for T-type thermocouple but it depends on the temperature range. Take a look at the graph below. K-type Seebeck...

View Article

Re: AD9361 initialization and calibration

thx, tlili I follow the HDL Reference Design , go to the GitHub and download the hdl-master code package.My working platform is ISE 12.4 and I use hdl-master\projects\fmcomms2\ml605(it's based on...

View Article

Re: AD8224 PCB Design Considerations

Hi Alireza,  The Vs+ pins 5 and 16 are internally connected. The same goes for the Vs- pins 8 and 13. The part will work if you have just one of the pins of each supply connected to the external power,...

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>