Re: ADIS16209 Assembly issues
Thank you! You might also want to try to measure the PROD_ID register, which is located at address 0x4A and contains 0x3F51. That will give you another simple way to verify that the internal processor...
View ArticleRe: EVAL-ADIS Software Does NOT Run on Win 7 64bit
One more question: are you experiencing this with an ADIS16209/PCBZ connected to J1 (pins 1-12) or only when you wire J1 to connect to your remote board? If it is with your remote board, you might...
View ArticleI have some troubles when I use CM408 and would somebody do me a favor ?
Hello ! I have some troubles when I use CM408 and would somebody do me a favor ?@Kelven.Mo 1,The SYS_FAULT pin will indicate fault(output low) when power on or after manual reset(by pulling down...
View ArticleRe: ADIS16209 Assembly issues
Hi Mark,Thanks for your responses.Question: if we are getting data, and not only that, it makes sense, but it is not within specs accuracy.Do we still assume internal processor might not have...
View ArticleRe: ADIS16209 Assembly issues
Dear Mark.Is there a way that we can talk?I feel we will be able to convey much more information to each other this way and we are running out of time! Thanks
View ArticleADV8005 4k2k(4096x2160)/30Hz output
Hi, Customer would like to have 4096x2160/30Hz output. I can't find any corresponding register settings. Can you please provide the settings for VSP(for any timing input) and Tx, thanks. The detail...
View ArticleLOG amp for OTDR
Dear Sir,I want to make a simple OTDR (Optical Time Domain Reflectometer).But because of optical connetor's reflection, there is not easy to get signal usingAPD+transimpedance amp + A/D converter. And...
View ArticleClik here to view.
Can AD9680-1000EBZ be connected with ML605(Xilinx) through FMC
I have ML605 and want to use it with AD9680-1000EBZ. Is that possible?
View ArticleRe: EVAL-ADV7625-SMZ HMDI passthrough
Hi Jesse, Software driver can be enabled/ disabled by opening/closing of the jumper J15 pins 1 and 2.When you open the jumper pins, software will be enabled and pass through worked.For running scripts,...
View ArticleClik here to view.
ADuM123x: Does it require external supplies for VDDA and VDDB?
I'm planning to use ADuM1233 in my project. I studied its datasheet today. There is something I'm trying to make clear which is not clearly mentioned in the datasheet. How are the VDDA and VDDB...
View ArticleRe: CEC-HDMI support in V4L2
Hi, 1. I'm not aware of any HDCP repeater support in V4L.2. What exactly do you mean by this? Drivers typically set up the infoframes according to the current mode.3. I think the main difference...
View ArticleRe: ADV7513:Register setting file
The ADV7513 is a HDMI transmitter. The only output clock is the TMDS clock on the HDMI output. Using different addresses should not cause jitter problems. Nor different polistry on the power down...
View ArticleClik here to view.
Re: WDTH_CAP problem with BF518
Hello,I am testing different configurations of timer6:*pTIMER6_CONFIG = (WDTH_CAP) | (TIN_SEL) | (PULSE_HI) | (IRQ_ENA) | (PERIOD_CNT);and I configured it to use interrupt priority...
View ArticleRe: AD9361 56MHz RX bandwidth
Hi Di thanks for your reply does the shape of the spectrum you get depends on ADC SigmaDelta architecture? I've another question about the analog filter RX/TX maximum bandwidth - from chapter "Filter...
View ArticleAD8303JRU
Does anyone have a datasheet available for the AD8303JRU device? I am trying to ascertain what the J meant on this device i am assuming RU is the 14-Lead TSSOP identifier but cannot find any datasheets...
View ArticleClik here to view.
Negative going voltage spike dilemma in the AD8219
I am using the AD8219 current sense amplifier in a battery charger design. The current sense amplifier input has a 8.3 milliohm sense resistor between the +in and -in pin. The sense resistor is between...
View ArticleRe: Power-up/down Sequence Timing in Digital Potentiometers and Analog Switches
Actually AD5260 and ADG1414 do have a VL input.Besides, if I read the datasheets correctly, the ESD protection diodes could be forward biased if I supply any voltage higher than the conduction value of...
View ArticleClik here to view.
Re: ADV7619 4K cable length
The HDMI standard does not define a cable length. It only defines an expected impedance. 4K (or 3G) should work fine over a good quality 3' cable. 25' will probably not meet the impedance...
View ArticleRe: PVP in BlackFin BF609
Hi Bill,THC block cannot process selective pixels. It can however process pixels within a region or outside a region (ROI). I think what you are looking for is to process only 1 of several channels....
View ArticleAD9361 initialization and calibration
hey guys. I work on AD9361 with my XILINX-V6AD9361 initialization needs calibrations.my question is for some specific parts,like BBPLL VCO or RF synthesizer charge pump,shoule I first calibrate them or...
View Article