Re: ADIS16405 sampling rate problem
With respect to #1, I wanted to share that this FAQ might be useful for understanding the concept for this type of experiment. The registers names and function are different in the example product but...
View ArticleRe: ADV7630 720P performance less than 1080P resolution
Thanks, Dave; i checked the V1.3 script file, find there is only one register update:1) 68 75 04 change to 68 75 44 ; ADI Recommended value; and i can not find the register definition of RX MAP...
View ArticleADV7842 Latency Questions [ADV8003 used as well]
Hello ADV7842 Experts, I have system requirements that require me to understand the time latency as video is processed through the ADV7842. My trade off is latency vs video quality. The latency will...
View ArticleRe: My DSP/DAC Project
[quote=Me]Clocks to the DAC's will be supplied from a single LMK00334 Fan out buffer which in turn will be fed from a Crystek CCHD957 ( 12.288MHz - Not listed but a custom ). Each DAC will feed the...
View ArticleRe: Issue plotting FFT in matlab using data from EVAL-AD7276
Hi Srsmoort, The AD7276 software uses windowing on the FFT and for this software it used the 7 term Blackman-Harris . Please try to use windowing in MATLAB . Regards,Jonathan
View ArticleRe: AD9225 CLK stop and resume
Hi PMHThank you for your prompt response and advise.I will consider a new gen ADC. Regards.
View ArticleRe: ADV7619 bypass mode
hi Dave:Now i use adv7619 as receiver ,and displlay to monitor ,The display color is different from the source ,So I think the CP maybe do something with the video,but if I set cp to bypass mode as...
View ArticleRe: ADAU1401 crystal oscillation
I am not a professional at all, but may be good shielding of the DSP will help?
View ArticleADF4350 output wave form
I have a question about ADF4350. Which is the base of the wave form of ADF4350?Triangular wave form? rectangular wave form? saw tooth wave form? Thank you.
View ArticleADAS1000 RLD + CM
Hello,I have a few questions about the ADAS1000 RLD + CMThe DB15 connectors has the following connections for pins 7 and 14Pin 7 - CE - Common Electrode, Master CM_INPin 14 - RLD - Right leg drive,...
View ArticleBody Marking for OP297GSZ?
Hi all, Anyone can share with me the photo of body marking for OP297GSZ? Can't get this information anywhere from the web. Thank you.
View ArticleRe: Body Marking for OP297GSZ?
Hi, Midori. Unfortunately, we are unable to provide information about parts in the EngineerZone community based on their markings. We suggest going back to your point of purchase to get this...
View ArticleRe: EVAL-CED1Z, EVAL-AD7626 and PuSAR Software Problem
Hi, This is being handled offline. Regards,Karen
View ArticleRe: do the AD5421's internal DAC and on chip ADC share the same reference?
Hi,thank you for your reply. Do you have the block about the on-chip ADC ? it's reference is independent with the REFOUT2 and REFOUT1 ? and how about it's reference voltage? How the on-chip ADC...
View ArticleRe: Problem with Video Encoder EI3 Extender Board
After discussion with friends, I believe the problem is that the interrupts for EPPI1 is not on. How do I turn those interrupts on? Thanks!
View ArticleRe: ADIsimClk with Zero Delay Function
Hi Paul, I just wanted to let you know that I sorted out the issue. I was using the AD9520-5 and AD9522-5 which doesn't have an internal VCO which would cause the program to crash when i tried to use...
View ArticleRe: AD7699 tSDIN time and tHDIN time
Hi Kotoo, Apologies for the delay. I think the datasheet should be corrected to change the TSDIN and THDIN descritption to refer to the rising edge. DIN Valid Setup time from SCK Rising Edge(tSDIN) 5ns...
View ArticleRe: Linux driver for the Vivado AD9361 Interface Block in Linux
Stay tuned - two teams - one always behind. -Michael
View Article