Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: ADT7461: Confirming how remote temperature is represented

Ok, so I found Table 10 in the manual which describes how offsets are calculated using the two bytes.  That seems to corroborate my understanding described above.  So you can either look at it as one...

View Article


Custom LDFs in CCES

Hi all,I've been working on porting a project for the BF561 with a custom LDF from VDSP++ to CCES. Since the import tool was not much help here, I ended up creating a new project and adding the...

View Article


Modifying ADL5511-EVALZ board

Experiment:I'm attempting to measure the RMS value of a 76 MHz carrier signal.  The amplitude should be entirely from random noise, however I'd like to modulate a source of the noise at ~50 kHz thereby...

View Article

Image may be NSFW.
Clik here to view.

Re: AD9361 SFDR

Thanks for you suggestion. The following is what I get which I set the TX2 1MHz offset from LO, while TX1 is set maximum attenuation.  Even more and worse spurs. LO is about -56dBc. where the max spur...

View Article

Re: Linux kernel support for HDL TRD

Can you cross test attached files. First try BOOT.BIN devicetree and kernel from the tgz.Then create use your BOOT.BIN, etc ... They were all build from yesterday.In the meantime we check if the...

View Article


Re: AD8333 double-ended output to single ended

There is nothing to say that you can not low pass filter on a differential signal. However, if you just need a single-ended signal, there is nothing wrong with using one output of the AD8333 and leave...

View Article

FPGA board

Can I use the FPGA board for EVAL-AD-FMCOMMS2-EBZ with EVAL-AD-FMCOMMS3-EBZ? They seems has the same interface.

View Article

Re: AD831 getting hot

Yeah, this is normal for the AD831.  It has a supply current of 100 mA nominal on a 9V supply, this is almost 1Watt of power it must dissipate from the PLCC package, which has no ground paddle to act...

View Article


Re: Using External Pots to Control Parameters

Thanks John.  I understand that I need to use an external ADC, but it seems the only input blocks available in the software are for audio inputs.  How can I set up an input to function as a control in...

View Article


adum3223 gives 900nS output with input of 100nS

in a totempole pfc we are seeing a strange effect with the adum3223 Driver.,  Although the circuit is normally working well, under certain pulse conditions the AD gives a 900nS Output pulse when the...

View Article

Re: EVAL-SSM2529Z

Hello, Here are the schematic and quick start guide. Best regards,Coleman

View Article

Re: i2C Isolation; 3kV working voltage

Hi, Thank you for your input so far. A couple of questions... You mentioned using the ADUM2400, then converting to I2C on the low side. This device takes an analog input?  If I wanted to convert to I2C...

View Article

Re: AD-FMCOMMS1-EBZ REF DESIGN- MODIFY+REBUILD

rejeesh:  For Number 2: a) How do you enable the channel data from Web Interface or command line?b) Where and how can I use the raw ADC data?         What signal name and what module does it exist?c)...

View Article


Re: ADAU1761 multi-channel audio on Zedboard

Hi, The ASoC framework currently does not properly support this setup. It assumes that on a I2S bus there are only two endpoints. I.e. one master device and one slave device. There is some ongoing work...

View Article

Re: Designing a Charge Amplifier for Triboelectric Dust Analysis

sanuzr,   ADI/PMI uses the "OP" prefix.  We do not make an OP129. Your schematic shows an OPA129.  "OPA" is the prefix for Burr Brown, which is now part of T.I. You could consider the Analog Devices...

View Article


Re: AD-FMCOMMS1-EBZ REF DESIGN- MODIFY+REBUILD

a) The osc application has some boxes you can select (don't remember exactly)- Michael will help you. b) These are the raw signals (same module/file where you are using the channel data)  wire...

View Article

Pink Noise Generator

I've been making use of the white noise generator with the pinking filter after it. For my first application it works perfectly, but I have another application where the requirements are a bit more...

View Article


Re: i2C Isolation; 3kV working voltage

The ADuM2400 is strictly a digital device, but I2C is only digital as well.  It is just that I2C is open collector and bidirecional.  There are buffers that allow conversion from 2 bidirectional lines...

View Article

Re: ADV7403 CVBS-525 signal shows too much jitter

Hi Wolfgang, We would expect the H-sync jitter to vary during the settling period after power up but 120ns seems a lot. There is approximately a 2.5 line delay through the ADV7403. When you measure the...

View Article

Re: FMCOMMS1 LO Driver usage

Thanks Dragos,  We ended up writing directly to these files in our software to implement the frequency change - works great. Thanks again,

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>