Clik here to view.
Re: ADIS16210 accelerometer resolution
Original post>>In the documentation you cannot find information that accelerometer has 12 bit ADC and is converted to 16 bit. Only information you can find is that sensitivity is ~61 μg/LSB on...
View ArticleRe: ADIS16210 accelerometer resolution
Original post>... and, please, put the proper information in the documentation. It is not fair. NevadaMark>>This was mentioned in my previous reply, but to address this specifically, the...
View ArticleAD5930 Gotcha's
Given a recent 'fight' to implement a saw sweep from 2285Hz to 3000Hz over a 150ms period with a 1.544MHz clock, I figured I would share my insights for anyone else who may encounter similar issues. I...
View ArticleRe: ADV7403 CVBS-525 signal shows too much jitter
Hello Wolfgang.We too use ADI video decoders ADV7184 and ADV7403 and too we have a similar problem for NTSC 525i mode (http://ez.analog.com/message/44300#44300).Decoder output signals jitter arises,...
View Articlethe ouput power of AD9957 evaluation board
Hi, Here I have a question about the AD9957 evaluation board. How can we improve the power of the output of DAC on the board? Thanks very much!Best Regards!
View ArticleRe: ADAU1442 Input ASRC Clock problem
What is your "start pulse source" set to (in "dsp registers modes 1" tab) ?Is your serial output a master or slave?
View ArticleRe: AD620 drift
Harry, Yes 305uV. It is measured at the A/D module. It is complete analog module. Panasonic AD8VI. Used as a module in a PLC rack. I check values from HMI device. At pages 6-3 and 12-3 there is info...
View ArticleClik here to view.
Re: ADE7758 Burden Resistor Value
Dear Dlath, I am calibrating the current channels by following the steps shown in datasheet of ADE7758 page 55. As a result, the channel C is able to get quite an accurate reading compared to the...
View ArticleRe: Gyroscopes
Hi Jim, I understand where you are coming from. What type of angle accuracy are you looking for? Are you also considering accelerometers for pitch/roll tilt and magnetometers for yaw-angle estimates?...
View ArticleADUCRF101 data encryption
Is there any data encryption support in ADuCRF101?Somewhere I noticed something about native (HW) AES 128 data encryption.I can't find any data encription support in radioeng API.(Manchester data...
View ArticleClik here to view.
Re: About ADP2164
THIS STILL NEEDS TO BE VERIFIED - STAY TUNED The Vin pin and PVIN pin can be powered from different voltages based on the abs max rating information on the datasheet.If there was a limitation on...
View ArticleClik here to view.
How to route TDM audio through multiple ADAU1701s?
Hello all, We're developing an audio mixer around a ring of ADAU1701s where each receives a TDM steam from its neighbor, adds in two analog inputs and sends the mix through to the next -1701....
View ArticleAD9650 Inverted CMOS Output
Is the AD9650 CMOS output inverted by default? By inverted I mean Gnd is 1 and DRVDD is 0. If yes, I must have missed something in the datasheet. If not, I need to figure out why my custom board with...
View ArticleRe: How to connect a 21369 EZ-KIT to ADZS-USBI2EZB and EVAL-ADUSB2EBZ
Ok, found it: SigmaStudio_for_SHARC_Users_Guide.pdf Daniel
View ArticleRe: AD620 drift
Hi dclmThe typ. zero drift of AD620A is 0.3µV/°C. Gain 660 gives 200µV/°C. Then comes the output drift typ. 5µV/°C.This 205µV/°C is amplified with 12 giving 2.5mV/°C. Over 40°C it is 100mV. Added to...
View ArticleRe: AD-FMCOMMS1-EBZ relayout issue:PIC firmware programming to a...
Dear Micheal,Can you provide a brand about a usb programmer?To update(no os driver),use a usb programmer conect to XP1(on board).then,how to do?Thanks.
View ArticleRe: AD5930 and AD5932 evaluation board software commands
Dear Sir, Sorry for the delayed reply. I tried you suggestion but it is not working. I did the following:-1. I connected the Board with Battey supply.2. I took another supply and connected it to the...
View ArticleRe: ADV7391 output drive current tolerance
Hi Eugene, We do not disclose the transfer function because we only recommend customers to use on of two RSET values, 510 or 4120 Ohms. Regards, Paul
View ArticleHow to show ADAU1442 SPDIF receiver status?
Hello. I would like to show ADAU1442 SPDIF receiver status and turn on MPx port LED.How to get info from DSP register (selfboot mode) about correct decoding of SPDIF signal?Thanks for answer.Adam
View Article