Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: unable to mount jffs2 file system in bf548

I saw you are using "ro" in your kernel command line, I usually use "rw", I see no other apparent error at this moment. However I think the best practice at this moment is to try to boot from the...

View Article


Re: ADV7511 Input Video Clock Delay

Assuming you are using single data rate communication for the video data, Register 0xBA (Clock Delay) allows you to adjust the position of the rising edge of the clock compared to the data. Based on...

View Article


Re: AD9119 clocking with ADF4350

I'm curious as to why this is of interest. We recommend the 100 ohm resistor is placed across the input pins. We have characterized the part with the 100 ohm resistor in the position we recommend. Are...

View Article

AD9361 No-OS Driver RF Bandwidth Parameters

We're evaluating the AD9361 for a WiMAX application using the No-OS software and the FMCOMMS2 eval board. For our 14 MHz RF Bandwidth application we found that the rf_rx_bandwidth_hz and...

View Article

Re: ADV7604 STDI not locking for 1024 x 2048

That info is certainly good to know - thank you!

View Article


ADCMP580 Eval

I have used the Analog evaluation board for ADCMP580 and I'm very happy with  I would like to reproduce such board in a small factor formI need to know what is the substrate used in the eval board and...

View Article

Re: ac constant current source

Hi Anna, AD8510 is  low current op-amp.Any suggestion on amplifiers for 200mA current source ? Thank you

View Article

Re: ADP1047, PFC output voltage regulation

Hey, Since there are no flags being tripped, I believe the problem is in the power train. For a 230VAC input either your switching frequency setting of 39KHz should be changed to 70KHz for chosen L=...

View Article


Image may be NSFW.
Clik here to view.

Re: ADE 7880 no-load conditions

Hi Heimo1 Please find below an alternative procedure that will help you implement the no-load functionality using ADE7880 in a uniform way, even if the phases are entering no-load condition one-by-one....

View Article


Re: unable to mount jffs2 file system in bf548

Thanks for the reply I tried to boot from the uImage... However i am getting the new error now as devtmpfs: error mounting -2, the kernel log is also attached below . If you have the uImage and working...

View Article

Re: How to calculate AD9858 DFTW and DFRRW ????

HiIn Sweep mode first we assigned CFR Address like  0x00 [7:0]     011010000x01 [15:8]   100000000x02 [23:16] 10000000 also Explain me about Load Delta Frequency Timer ????this bit be high or low in...

View Article

Re: Eliminating the cable capaciance

Hi, Iam using it with the range extension circuit. Its supposed to measure the capacitance b/w exc and cin. But i guess there's some leakage to ground through cable capacitance. Is there some way to...

View Article

ADIsimADC in MATLAB2011

Hi, I'm trying to use ADIsimADC as the source of data for a research in my university. Using the VisualAnalog interface everything is fine, but seeing as I need data from many frequencies and...

View Article


Re: ADV7182,ADV7340 and ADV7511 video decoder/encoder configuration

Hi , We are using ADV7511 for DVI Out , ADV7182 for CVBS Input and ADV7341 for CVBS output. ADV7511 working properly as per expected. ADV7182 register configuration is done as shown in the attached...

View Article

Using the ADAU1700/1701 DSP for Radio Communications

We are currently working on a multimode radio transceiver and one of the functions we wanted to add was DSP primarily for audio signal processing on SSB receive. This in reality is a low intensity...

View Article


Re: ADXL362 datasheet questions

Hi,  1. You can find that in item 6, the part begins the measurement in wake-up mode, this means the ODR is around 6Hz, then 30 samples means 5 seconds.2. Half_BW does not impact ODR, it only impact...

View Article

Re: Some ADXL362 spi-data issues

Hi liron, 1. 0x3D is nothing special to the ADXL362. I would suggest you to check the program to see whether there is some conflict on the SPI interface. The power supply can be monitored too, to see...

View Article


Re: ADI Inertial Sensor Evaluation System and win7 x64

Hi, Please try the driver on the link below: ftp://ftp.analog.com/pub/iMEMS_Sensor_Eval/ISEB_USB_Driver/.All the EVAL-ADXL3xxZ-M can work well under win7 x64 with this driver.Hope this can help. BRNeil

View Article

Re: ADxL345 and ADuM2401

I first connected the ADxL345 to the MCU without the ADuM2401 and I got good readings (from the ADxL). Than, with the same firmware I added the ADuM between the MCU and the ADxL235 (while supplying two...

View Article

what is max length of the video data output trace?

ADV7611 Datasheet have no discription about the max length of digital output trace. Can anybody help me? The trace length (both data and clock) on my system will be 30cm. I don't know if the board can...

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>