Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: How to switch to another ADC channel on the fly?

Can you check the MMR ADC1CON, as documented on Table 24, page 38 in the User Guide you can predict the channel settings. You also can directly write to the MMR ADC1CON to select the inputs for your...

View Article


Re: ADV7182,ADV7340 and ADV7511 video decoder/encoder configuration

Hi , We are using ADV7511 for DVI Out , ADV7182 for CVBS Input and ADV7341 for CVBS output. ADV7511 working properly as per expected. ADV7182 register configuration is done as shown in the attached...

View Article


Re: ADV7182,ADV7340 and ADV7511 video decoder/encoder configuration

Hi , ADV7340 colour issue is solved.For ADV7182 still noise problem we are facing. We are configuring ADV7182 internal test pattern by writing register 0x11 to 0x14 register.Color BAR pattern coming...

View Article

Image may be NSFW.
Clik here to view.

Re: Exceed Input Common Mode Voltage

Hey Kris, in the picture below i illustrate the circuit.in the first configuration R1 and R2 were 0R, now i replaced it with a 100R resistor so that the current is limited to less than 8mA. Fortunately...

View Article

Image may be NSFW.
Clik here to view.

Re: ADE7878 with smaller WTHR VARTHR calculates wrong energy values

Hi Dlath, I have not had any problem with ADE7758 because i am designing now my new hardware with ADE7758. Before i finish the new pcb, i just wanted to ask you about chip reset mechanism. Is there any...

View Article


Re: AD8475 using IN 0.8x for aditional low pass filter?

Doesn't anybody know about this AD8475?

View Article

Re: ADV7511 Linux Examples running on Xilinx Zynq Board

Hello, Please download the reference design (for the desired board) from github. For example, this is the design for the ZC706:...

View Article

Re: AD8475 using IN 0.8x for aditional low pass filter?

Thanks for that "classification"!!!Und tschüss...

View Article


Re: ADE 7880 no-load conditions

Hi hmani!Thank you for the details. I will try your approach! I do not use the CF-outputs and I am accumulating the energy in my microprocessor. My approach will be as follows:Set VANOLOAD as you...

View Article


About voltage of external regulator at ADAU1452W

Dear support team, I have a question about configuration of power for DVDD at ADAU1452W. Q.Is below configuration of DVDD acceptable?     VDDIO = 3.3V     External PNP transistor input = 1.8V I...

View Article

Re: adxl345EV problem

Hi Lama, I am worry about there is something wrong with your hardware. Please check your I2C connection according to Figure 40, on page 18 of ADXL345 datasheet. Please try to read DEVID firstly to make...

View Article

Image may be NSFW.
Clik here to view.

Query about ADRF6655's Conversion Gain

Hi, thereI brought an EVB of ADRF6655 from your distributor and tested it. Here are two queries that need your help.1, I measured ADRF6655 output signal through spectrum analyzer.But measured...

View Article

Image may be NSFW.
Clik here to view.

Re: Vrms calibration in ADE7758_SPI with Arduino

Hi Dlath, I had disable the LINECYC to read the energy register only and the AWATTHR seem to increase constantly. When the load increases, the AWATTHR register reading increases with every readings. I...

View Article


Re: adv212_firmware_load

Hi Dave, I just changed fpga pins as LVCMOS33 and the Aadv212 started to init succesfully but not stable. One time it inits another time it can not. What i mean is saying is that i m waiting active low...

View Article

Re: Voltage +-50V/100mA driver

Hi Stefan,  Your +/-50V requirement at the output really narrows down the choices for the driver. I would recommend that you take a look at the ADA4700-1 for that purpose. It has a very wide supply...

View Article


Query about AD8370

Hi, there We are using AD8370 VGA in one of our projects at 140MHz.Although,I went through the datasheet i was not able to find the IP3 behaviour and gain step resolution @140MHz at low gain mode and...

View Article

Re: ADL5565 FPBW specifications

Dear Jim, unfortunately I can't accept with you.Looking on your answer we can not trust to the "Test Condition/Column" column at all?6.75 GHz is mentioned on the third page and any engineer immediately...

View Article


Re: FMCOMMS1 : problem with I-data

Hi Alex, I think I found a part of the problem in "ad9122_tune_dci". This function always returns an error the first time the software is launched. But if we launch it again, without turn off the...

View Article

Image may be NSFW.
Clik here to view.

BF524 USB block power

Hello, My board was designed with BF524. BF524 operates as USB device. The circuit is coped below and the same as evaluation B/D.Occasionally, the following situation happens while operating.- VBUS...

View Article

Re: ADV212 in decode mode, 1080i-50Hz

Hi again! Up to this moment, I used only small bitrates below 20MBit/s for the ADV212 encoder. Now, I need to set-up the encoders for about 70 MBit/s. However, the encoders generate the total output...

View Article
Browsing all 22625 articles
Browse latest View live