Re: error DUT not detected
In the lab, the current that we get is approx 230 mA in 1.8V and 90 mA in 3.3V.
View ArticleRe: ADE7878 Evaluation Board - Beginner
David, In continuation to my last post, I need to log Total Harmonic Distortions in the supply. What do you propose I should do for that?
View ArticleRe: Assembly code for ADuCM360
I will proceed as you suggested and then get back to you, Thank you
View ArticleRe: SPI communication having ADuCM360 as slave and Host master
I will get back to youThank you
View ArticleRe: ADuC702x power on error
Sounds somehow the part gets latched up if you switch on the power. What filters do you have in the power-supply line? See recommendations in data-sheet please!For entering the Download-Mod you must...
View ArticleClik here to view.
Re: What is the reason for using the O_TMPFILE flag ?
Thank you,By using the 2014_R2 branch, my compilation issue is now solved.
View ArticleRe: Parameters of ad9523 in fmcomms1
Hi Dragos again, What is the minimum DCI clock tha ADC can handle. Can I set it to 16 MHZ!? Regards,Jet
View ArticleRe: How does overlay PACKING works?
Hello Jobo23, Thank you for this answer but I also read pages 3-45 to 3-50 from the Linker and Utilities Manual. Your answer does not answer my question. I would like to understand what B3 or B4 means...
View ArticleBF533-STAMP with libusb, ccid, pcsc-lite, libacsccid1 - is it possible?
Dear Blackfin Buildroot developers! I have some problems with compilation of rootfs for BF533-STAMP.What I have:Analog Devices (AD) BF533-STAMP boardAD toolchain - 2012R2, 2014R1_45AD buildroot...
View ArticleRe: VGA for 10 to 15MHz (DC or AC) Signal for ADC input
Hi, Chris, The AD8370 is one of the widest range digitally controlled differential VGA, but the gain range of 45 dB is still less than your requirement (20 log (7/10m) = 57 dB), so more than one...
View ArticleRe: AD-FMCOMMS4-EBZ with ZYNQ-ZC706 problem
Yang, Are you getting the same "Unsupported PRODUCT_ID" error? The error means that the SPI communication between the ZC706 and the AD-FMCOMMS4-EBZ is not working.Can you also try the Linux image (Zynq...
View ArticleRe: FMCDAQ2 Out_A 30dB lower than Out_B
Hi Stuart, Did you also try the Linux image (Zynq Quick Start Guide [Analog Devices Wiki])? We will take a look at the no-OS software - maybe the problem comes from there - and we will let you know the...
View ArticleRe: Special Usage of HMC783LP6CE
Hello Marty-san, We couldn't get good spectrum of VCO output whe we conecting all pins accrding to your idea. Are there any word of caution for using HMC783LP6CE as VCO? Or can't we use the HMC783LP6CE...
View ArticleRe: EVAL-AD7982SDZ : sampling rate and updating the display data
Hi, ysuzuki. I have tried the software with the EVAL-AD7980SDZ and I had no problem seeing the display at 100ksps. Did you get the software from the AD7982 product page? Regards,Karen
View ArticleClik here to view.
Re: AD-FMCOMMS4-EBZ with ZYNQ-ZC706 problem
Dragos,I got the same error when I used the new progect with vivado 2014.2.I used the linux image. the device block in iio is empty.There is the picture.Thanks,Yang
View ArticleClik here to view.
Re: AD9548 Eval. Board SPI Programing
Thanks for your quick reply. Problem looks like both GND and SPI programming.Everthing is OK now.
View ArticleClik here to view.
Re: AD9434 difficulties
Hi David, Please have a look at the snapshot collected with ChipScope:this shows the ADC-Signals after the input interface. All data is now parallel (DDR from ADC), and we see the test pattern (D0-D5 =...
View ArticleRe: Documentation init struct query
Hi Michael, What do you refer to by "AD9361 Design Forum"? Can you give me a link? I could not find this forum. The Wiki Page you sent me the link is not useful, it only contains a screenshot and not...
View ArticleRe: Questions about AD9361 AGC Fast Attack Mode
I have the same behavior. The AGC configured in fast attack modes does not unlock. In my case I generate the signal by using the TX channel of the AD9361. I first send one burst with TX attenuation...
View ArticleRe: Mapping I and Q samples to dac_ddata_1 and dac_ddata_0 in fmcomms1
Hi Rejeesh, How it can be that data format of the axi_ad9122 is set to 2's complement (register 0x4048 bit 4 is zero) and the DAC data format is set to binary format (register 0x03 bit 7 is set to 1)!?...
View Article