How to access all the software driver commands for EVAL-ADV8005-SMZ
The pdf labeled BF_800x_System_Commands_20140707 on the support page does not list all available commands. For example, PIP commands are not listed by do appear in terminal on the help list. The help...
View ArticleRe: Can I use the IBIS(ADV7511W) under the condition 3.3V?
Hi GuenterL.Thank you for your answer. Inside of ADV7511W's IBIS model , parameter is ...[Voltage Range] 1.8 1.71 3.6And with your recentry...
View ArticleRe: CMOS AMP contains no BJT
Hi Alexey, Apologies for the delayed response. Before I suggest parts for you, may I know the following application information?1. What is your supply voltage?2. IVR?3. Output Voltage Swing?4. What are...
View ArticleRe: 【Need help】: question about font size in blimp3.7 adv7626 project
hi Jeyasudha.M: thank you for your reply. 1, and i want to know whether the blimp3.8 is available for downloading? 2, if i open project file designed with blimp3.7 in blimp3.8, can all the...
View ArticleRe: OSD Alpha Blending in Adv8005
Hi, we are currently looking into your question for this configuration and will get back shortly. Regards,Dominic
View ArticleClik here to view.
Re: Cannot get ADV7180 to display video through ADV7513
I just tried setting the ADV7513 Input to 0100. And the HPD pin is around 4.3V which is well above the needed 1.2V requirement for HPD to be high.
View ArticleRe: ADV7612 incorrect FIELD0_TOTAL_HEIGHT content
My driver use initialization sequence from this linux driver (which is uncommited)....
View ArticleRe: ADV7612 incorrect FIELD0_TOTAL_HEIGHT content
We typically recommend customers start with one of our evaluation boards so that they can have a known-good hardware platform and software driver. Since you are developing a software driver for a...
View ArticleRe: ADV7612 incorrect FIELD0_TOTAL_HEIGHT content
Thank you very much for the information. I can't download ADV7612 Recommended Register Settings.pdf, it seems like this link is...
View ArticleRe: Solutions for bad Load response of adp1048 interleaved pfc for a 2kw...
Hi, I looked at your waveform again and it appears that the power supply is shutting down when you do a load dump. Can you check the following: (i ) The first flag ID in the GUI (ver 2.2.8)(ii) A...
View ArticleRe: ADV7612 incorrect FIELD0_TOTAL_HEIGHT content
Yes, we are having trouble with some links after a recent website upgrade. I will email you that file. However, the scripts are probably a better starting place. -Matt
View ArticleConfigurations for KC705 with FMCOMMS1 to run XCOMM example
Hi, I started working with FMCOMMS1 using KC705. I went through the steps building the project (noOS-Driver) AD-FMCOMMS1-EBZ Quick Start Guide on Xilinx FPGA Boards Without OS [Analog Devices Wiki]....
View ArticleClik here to view.
Re: sigmastudio 3.11.1 support for adau1372
Hello Srikrishnan, After copying the ADAU1372.dll file to your SigmaStudio program folder,close and re-launch SigmaStudio. The new IC should show in the toolbox after selecting New Project:...
View ArticleRe: EVAL - AD7730EB Source Code
HI Jarwin, Thanks. I have already had that software. But I would like to control the evaluation board via matlab, what should I do? Best,Junyi
View ArticleRe: 【Need help】: question about font size in blimp3.7 adv7626 project
hi Jeyasudha.M： thank you for your reply. BRXutao
View ArticleClik here to view.
Re: i am looking for suitable replacement for SSM2166 (mic preamp)...pls...
Hello Naveen, Sorry that this difficulty remains. I had confused the SSM2166 with the differential-input pre-amp ICs often used where I work, but actually the SSM2166's data sheet shows it...
View ArticleRe: AD5933 and Evalutaion software to measure complex impedance
Kevin.G,I think the equations should read like this (the signs are reversed): RFB >= (0.25V / Vexc) * (1 / PGA) * ZmaxRFB <= (3.2V / Vexc) * (1 / PGA) * Zmin For example, if my output excitation...
View ArticleRe: Beamforming with sigma DSP
Hi Miguel, Good day. I am actually new to SigmaStudio.Do you have any document that describe on how to setup a basic beam forming (2 mic would be good enough)?It would be best if you have any reference...
View ArticleRe: ADP5054 ADISimPower Tool
Dear Kevin:I can't find your E-mail address, can be directly sent out e-mail to me? my E-mail jackbcp@gmail.com, thanks Best Regards, Jackey
View ArticleRe: ADA4870 insufficient gain.
Hi Joeal, Can you retest your circuit without the 50 ohm resistor you have across your voltage source. Phil
View Article