Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: ADXL375/377 band width request

Hi Kevin, For wider BW requirment, I would suggest you to check ADXL001. Attached is the datasheet for it. BRNeil

View Article


Re: LDR creation error in CCES

H Craig,The error occur for both the Debug and Release configurations.I have tried with example project BubbleSort with same options, no such error occurs.I am using CrossCore Embedded Studio 1.1.0....

View Article


Re: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad

Hi Manish, I think this question is related the one on this post: https://ez.analog.com/message/168484#168484 If you still have issues please let us know and we'll try to help you further. Thanks,Andrei

View Article

Re: Simulink ad9361 transmitting and receiving

Hi David, The amplitude of the Rx data depends on the gain settings for the Tx path and the AGC settings for the Rx path. To increase the amplitude of the received data you can either increase the Tx...

View Article

Re: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad

Now SD card is working with ubuntu image fileand I have done all updates for IIO OSCILLOSCOPE ,LIBIIO by sudo adi_update_tools.sh command on terminalNow I have interfaced window pc (where matlab is...

View Article


Image may be NSFW.
Clik here to view.

ADE 7878 Evaluation Board

Hi Guys,  I am new to ADE and was planning on using the ADE 7878 evaluation board for metering purposes. I went through the data sheet, application notes and the user guide.I would like to know if...

View Article

Re: vivado, fmcomms1, and kc705

I would ask Xilinx. It could be that you have chosen NOT to install the specified device.

View Article

Re: ADAU1701 External Delay: Idle Thoughts on Boxing Day!

Here is an optimized version that includes memory address calculation.  I realized it was more efficient for both memory use and instructions to go to three downsamples in six sample periods, so the...

View Article


searching for a low-frequency, lock-in solution

Hello Analog,  I'm looking for a the simplest way to do a low-frequency, high-resolution lock-in solution for multiple 4-wire rtds. (If I can't find one, I'll try the AD7794 without lock-in.)  The DAC...

View Article


Re: Connecting ADuC7020MKZ to JTAG-Emulator

Think the easiest way is to look-up the JTAG-connections on the ADuC7020 Quick-Start Evaluation-Board.

View Article

Connecting ADuC7020MKZ to JTAG-Emulator

How to connect a JTAG-Emulator to the ADuC7020MKZ?

View Article

Re: FMCOMMS2 - external reference clock

I followed all the directions here but I'm getting a few errors on boot and I can't display a signal in the oscilloscope. ad9361 spi32766.0: Calibration TIMEOUT (0x247, 0x2)ad9361 spi32766.0:...

View Article

Re: AD9361 AC701 no-os customized for CMOS mode

Istvan, I made this change in the dac_init function in dac_core.c to set the register to a value of 1 instead of 3, but this did not change the functionality of the dac_valid signal.  I hardcoded...

View Article


Excessive AD835 offset with gain = 37

I'm using an AD835 as a voltage-controlled amplifier with gain up to +37 (31 dB).  Attached is a simplified circuit diagram.  GAIN ranges from about 25 mV to 1 V, and SIGNAL is an audio signal no more...

View Article

Re: Connecting ADuC7020MKZ to JTAG-Emulator

But where bin from jtag module correlate with the pins from board ?

View Article


Image may be NSFW.
Clik here to view.

AD9912 power supply quality?

How clean do the +1.8V and +3.3V power supplies need to be for the AD9912 for noise voltage and ripple?My application does not use the on-chip REFCLK multiplier or PLL circuits.The DAC has an internal...

View Article

erroneous acceleration values reported from ADXL375

I am facing a strange issue reading acceleration values from an ADXL375 part using the SPI interface.When I read just a single acceleration value (eg: DATAX1) the value is reported fine.When I modify...

View Article


Image may be NSFW.
Clik here to view.

ADAU1702 hysteresis settings

I don't understand the auxiliary ADC hysteresis settings: FIL[1:0]00  4-bit hysteresis (12-bit level)01  5-bit hysteresis (12-bit level)10  Filter and hysteresis bypassed11  Low-pass filter bypassed So...

View Article

Re: AD5628 reset DAC to zero problem

The /CLR pin should be tied high for normal operation.

View Article

Re: Problem:i cannot get the right data from the ADIS16448 when it is waggled

What values are in the SMPL_PRD and SENS_AVG registers?

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>