Emulator ICE-100B error
Hi,I am using a customized board based on the BF-538F. I am trying to emulate the using the ICE-100B emulator but I am getting the following errorError: 0x80048015Error Description: Open Device Driver...
View ArticleClik here to view.
ADV 7403 Video Decoder Power Consumption
Hi, I am using ADV 7403 Video Decoder in my design to convert the YC(luma and chroma) Analog Input signal to Digital signal in BT .656 standard. I have powered-on my system. I have found few...
View ArticleCustom design in Zed board, FMCOMMS-EBZ, Reference design
Hi, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is there?...
View ArticleA suitable interface device for AD7762 or AD7763 VOH
HiI would like to select the suitable interface device, as level translator to 3.3V, for AD7762.An interface device's Vinh min is mostly 0.7 or 0.65 X Vdd min, I think.It is about 1.65V at vdd=2.5V.But...
View ArticleRe: IIR filter crashes on the fly
Hi Dan, Did you get your -1701 to safeload your filter coefficients? Bob
View ArticleClik here to view.
Re: ADV7619 pink lines after switching from unsupported to supported resolution
Thanks for your quick response, will try your suggestion.
View ArticleRe: ADM3251E DCDC enable/disable
Hi MMA,Thanks for your reply.Let me make sure if my understanding correct. Internal Power Enabled : 4.5 to 5.5VInternal Power Enabled : 3.7 to 4.5V Internal Power Diabled : 3.7 to 3.0VAs of 3.7V to...
View ArticleClik here to view.
AD7265 Fully differential Configuration help
Hi I would like to use AD7265 in fully diff configuration for data acquisition system.I confused on the Differential input range mentioned on the datasheet. My requirements are VDD: 5V...
View ArticleRe: AD7476 behaves like reference is only VDD/2.
Hi Dneise, According to the datasheet specs, LSB is equal to VDD/4096, so you are right that it should be around 1.22mV. There are 2 possible elements that you can look into: First, what did you use...
View ArticleRe: Issues with EVAL-AD7294-2SDZ Current Sensor
Hi, Arne. Do I understand that you installed the same Rsense for both evaluation boards? Can you send an illustration for both of your setup including the modifications you have applied? Please also...
View ArticleADE7878 Evaluation Board - Beginner
Hi, I am a beginner in Analog Devices. I need to make a Data Logger and after having a look at numerous SoC's I decided to zero in on ADE7878 Evaluation Board. I went through the Manual of the...
View ArticleRe: [Need Help: Chinese character can not display normally under blimp3.7...
Hi Xu tao, I have checked your project. You have not updated the appropriate Chinese Unicode values in Unicode settings. We have corrected the same in the updated project. Please see the attached...
View ArticleRe: PIXC and EPPI 's RGBFMTEN can be used together ?
I‘m sorry.PIXC register configuration wrong.
View ArticleClik here to view.
Re: how to downlaod Eval ADT7x20EBZ software
Hi,I had use your attached to install, still have some error,Do you have any suggest? Thanks.
View ArticleAD9913 interfacing with LabVIEW
Hi, I am planning to control the AD9913 by using LabVIEW. But I am newbie in this, and I don't have the evaluation board for AD9913. Does anyone know how to connect the AD9913 in order to program it...
View ArticleClik here to view.
AD9364 Tx monitor gain settings
Hello, I'm trying to understand the correct way to set the Tx monitor path gains. There is an example (table 2) in AD9361_TX_Power_Monitor_v2.1 document, which has Tx Mon Low Gain = 0 (I assume that it...
View ArticleClik here to view.
Re: ADIS16448 can't return ID during one read
Thank you for your help. I have resolved the problem, because I didn't raise chip select for 9 us after sending 0x5600. According to the datasheet, DIAG_STAT[7] will rise to 1 when the xMAGN_OUT and...
View ArticleRe: ADE7754 interfacing with Atmega16
Hi I am facing the following issues with the ADE7754 Eval board. No communication established when trying to establish connection with PC via Parallel port. I use USB converter is OK but when i enter...
View ArticleRe: ADE7878 Evaluation Board - Beginner
Hi dlath, Thanks a lot for your reply. I would want to measure all the values that I am able to measure using ADE7878 i.e., r.m.s Voltage and Current, total active, reactive and apparent energy,...
View ArticleRe: Query about ADF4159 Sweep Glitch
I will investigate changing the reference. The VCO is a 10-12 GHz model. I am using the divide by 4 output to feed back to the PLL, approximately 2.5 GHz. Will try manually programming the PLL to sit...
View Article