Re: ADV8005 can not output 4k
Hi, software driver version is below: >rev Command is REV Argument1 is Argument2 is Argument3 is REV...
View ArticleADV3205 Eval Board information
Hi, I will use AVN3205 for analog video matrix switch,so I need some references about using AVN3205.Could you provide schematics and board layout of AVN320 Eval board? Reards,Se-woong
View ArticleADN4600 for 3G-SDI
Hi, I have a simpe question about ADN4600.I want to use ADN4600 for 3G-SDI switch, but I can't find your mention about 3G-SDI of ADN4600.Are there any problem to use ADN4600 for 3G-SDI switch?Or can I...
View ArticleRe: ADV8005 can not output 4k
Hi, the video displayed of 4k output is successed, but i do not anything,just type "pout 4kx2k30" command in console,it is weird!!!
View ArticleClik here to view.
ADV7619 output is instable if it could not connect the same GND together with...
Dear Experts,My customer designed ADV7169 in the video processor project. There are multi pcs of ADV7619 inside the design (ADV7619 connected straight into FPGA), and there are also HDMI Tx behind...
View ArticleRe: adf4350.h
Unfortunately No. The Cypress chip acts as a USB/SPI bus bridge.I don't know what your try to achieve. Wanna use the EVAL board in some kind of application?The eval board is just for evaluation...
View ArticleRe: EVALZ-ADN2915
Dear Teodor, Which company do you work for? Who is your customer? Could you please send me one email at dongfeng.zhao@analog.com? We can talk about this wonderful device off line. Merry Christmas!...
View ArticleRe: Does the AD9361 Filter Wizard version 3.0 work correctly for receive FIRs?
Thad: Yes - when we switch from Tx to Rx it should switch from Interpolation to Decimation - Tim can fix that. (Thanks for reporting). As for the Fstop question, today, the limit is the same (1/2 of...
View ArticleRe: Does the AD9361 Filter Wizard version 3.0 work correctly for receive FIRs?
Hi Thad, Concerning the Fstop, we are comparing it with the "data rate" you specified, which is 12 MHz here. So Fstop should be less than or equal to 12/2 = 6 MHz. Fstop is not compared against the...
View ArticleRe: Very low sensitive of AD9874
PMH, thanks for answer. R4/R5 and R6/R7 do not used together. R4/R5 used only when R6/R7 are removed. I do it for check an internal ADC. The results shown above was measured when R4/R5 were removed...
View ArticleClik here to view.
Re: ADR421 long term drift graph data
Hi Tony, Below is the graph for ADR421 long term voltage drift. Please let us know if you need something else. Regards,Phil
View ArticleConfused about CEC_CLK on ADV7513 with ADV7180
I plan on using the CEC feature later, but I noticed there is no CEC_CLK PIN on the ADV7180(Decoder) while there is one on the ADV7513(HDMI Transmitter). I have wired the CEC from the ADV7513(HDMI...
View Article21489 spi slave boot flow control
From the app note: http://www.analog.com/static/imported-files/application_notes/EE_177_SHARC_SPI_Slave.Booting.Rev.3.01.07.pdf I see that some processors have a flow control bit when booting in SPI...
View ArticleRe: 21489 spi slave boot flow control
This is really up to you.The first chunk (384 32 bit words) is sucked in via DMA, so that is faster than you could supply it.After that the boot loader is executed which is the code that is inside this...
View ArticleClik here to view.
Re: image processing demo for BF527 in Blackfin Processors
Hi, Thanks for Quick reply.Where Most of Software module file contain Board rev2.2.But i have ver 2.0 BF527 along original CCES and VDSP++. I want to run Blackfin...
View ArticleRe: Sine wave in No-os driver FMcomms1-ebz
DragosB, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is...
View Articlebf609 running frame capture example
Hi,I was trying to run the frame capture example for bf609 ez kit and video decoder EI3. I get the following messages in the console. UYVY422 video, Capture frame to fileDecoder Soft Config -...
View ArticleClik here to view.
Re: ADV7403 power supply
I have used 10uF, 6.3V Rated capacitor to CAPC2 and CAPY1 pin, in my design. Whether it cause any issue?I have powered-On the board. I did not find any capacitor damage / fumes on the PCB. Please...
View ArticleRe: ADV7403 power sequencing
Thank you for the recommendation regarding power - on sequence. In my design I have provide 3.3V, 1.8V Analog and Digital Power Supply Simultaneously. In the datasheet, or reference manual I did not...
View Article