Clik here to view.
Re: High Pass Filters for AD620 and AD820
Thanks for the information Emmanuel, Does the high pass filter seen in the image you supplied require an OP1177, or can the same principle be applied to different components? The current context of...
View ArticleClik here to view.
ADF4350 and ADF4351 evaluation board control software
The latest ADF4350 and ADF4351 software is attached. This is compatible with ADF4350 and ADF4351. Installation process:1. Disconnect any evaluation board2. Download and run the attached installer3....
View ArticleClik here to view.
Re: ADF4351 settling time calculation using teh EVAL baords
I forgot that the band select clock time in R4 should be set to 500 kHz. This works in conjunction with setting the band select clock mode high. Try these settings:I set your channel spacing to 500 kHz...
View ArticleRe: EVAL ADE7878 EBZ- wavesign sampling data acess
Hello hmani, I will be very thankful if you can get me this codes you've cited.My email is augusto.d.rodrigues@hotmail.com. I'm not really familiar with labview codes, but I'll make through it. For the...
View ArticleRe: AD-FMCOMMS5 Multi Channel Oscilloscope
Thanks. I ran it twice, but forgot to reboot in between and running it a third time after rebooting caused more of the updates to take effect. With the latest version I am able to collect IQ data from...
View ArticleRe: DVI to VGA active RAMDAC using ADV7123
what FPGA would i need, how much would it cost and how would i program it? i have no idea about programming hardware the monitor is a Sony CPD-G520P CRT computer monitor, not really specific...
View ArticleClik here to view.
Re: High Pass Filters for AD620 and AD820
Hi Ben, You can choose other opamps as long as you are sure that it is operating within the the range specified on the datasheets. I am actually confused if you are trying to build a high pass filter...
View ArticleDrivers for Octal Ultrasound part
Hi EZ, Do you by any chance have a SPI drivers for the AD9671 and AD9106? I'm specifically looking for similar to the IIO DDS drivers and IIO A/D drivers already available. Thanks,Ryan
View ArticleRe: Drivers for Octal Ultrasound part
Those are already planned - but not done yet. What is your timeline? -Michael
View ArticleRe: Drivers for Octal Ultrasound part
Hi Michael, Protos are to be completed by the end of the year, but it would be very helpful to get the drivers ASAP as we could use the FPGA to drive the evaluation kit for the software development now.
View ArticleRe: Drivers for Octal Ultrasound part
Given the Xmas break approaching fast - this year is probably not feasible.Early next year is on our radar. -Michael
View ArticleRe: Drivers for Octal Ultrasound part
OK, I guess I will try to modify existing drivers then. Thanks.
View ArticleClik here to view.
Re: ADP7142 Configuration with 24 - 5V
Gonzalo, to answer your first question, the tool calls out(4) 402 ohm resistors in parallel. Please see the diagram for the placement in the circuit. Rin is the one we are talking about The web tool...
View ArticleClik here to view.
Re: ADF4351 settling time calculation using teh EVAL baords
I am generating the plots with ADIsimPLL. I have attached the simulation I am using. The simulation is also used to design the loop filter. You will need to download our free tool to open the...
View ArticleRe: FMCOMMS1: Clock Genarator adjustments...
Hey...@@@@@@I almost came to the conclusion that my current problem is in AD9523-1. Not considering the 20MHz input generated by AD9548 on RefB, a 20MHz comes from a function genratior on RefA causes...
View ArticleAvailability of the FMCDAQ2
Hello, Can you give me an idea of when the FMCDAQ2 will be generally available for purchase, especially in the UK. Also I see that there is an HDL design for it but no softwaredrivers yet on the ADI...
View ArticleClik here to view.
Re: Simultaneous I2S INPUT and OUTPUT from DSP
Hello Juha, Yes, what you are looking to do is possible. For example for a product like the ADAU1701, you can bypass the stereo ADC and four DAC outputs and use it as a "digital-only" interface to an...
View ArticleRe: AD 607 impedance
Hi Suppo, Mixer input impedance is shown in TPC2 in the datasheet on page 11. We usually have an off-chip 51 Ohm shunt resistor to ground, to set a 50 Ohm input impedance. This is shown in Figure 12...
View ArticleClik here to view.
Re: 16-Lead Standard Small Outline Package, with Increased Creepage
Hello Sofy, The 16-RI and 20-RI reel has the same dimensions as the "RW/RB 20, 24" in the table: DaveC
View Article