Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: hi.in ADI Water Analysis Solution for pH Meters.pdf there is a block in...

hi erbi i think there is aproblem with this scheme using for the source of current because most of water conductivity meters have the impedance of 2000 to 3000 Mohm and they can be to about 100 Mohm or...

View Article


The measurement conditions for the settling time of a current DAC

Hi The settling time of a current DAC is depend on output op amp feature.For example, AD5546 datasheet say it was using AD8038.But I can't see the measurement cuircuit or external condition.Is it No...

View Article


Image may be NSFW.
Clik here to view.

ADP5090 User Guild Question

Dear Sir:I Study ADP5090 UG-708 "EVAL-ADP5090 User Guide" document. The Figure 4. ADP5090 Pin 4(R7) show NC But Table 2.Bill of Material show R7-Resistor, 20k. Which one is correct? If R7 is NC ADP5090...

View Article

Re: Modifying debug_nets.ltx file

Thank you very much  and for others ;This will provide you a little bit more comfortable. make it into .tcl file and add it on menu. (you have to open h/w manager first)   connect_hw_server -host...

View Article

Re: build AD9467-FMC project in vivado

Thanks Dragos for you reply, just question: can I bypass the axi dma and capture data directly from the adc to the PL, as all my design runs on the PL of zynq soc, any such  example? thankskhaled

View Article


Image may be NSFW.
Clik here to view.

Re: AD-FMCOMMS3-EBZ Crystal

Crystal phase noise performance data as well as other device parameters are available from the crystal manufacturer, Epson.

View Article

Re: ADV7619 CEC and HPD

Please check out the pull ups as shown on reference schematic at this link Advantiv™ EVAL-ADV7619-7511 Video Evaluation Board

View Article

Re: L1 data memory stalls/ asm information

Hi Christoph, There is no further action required from you, unless you want to attempt to optimize your code to avoid the additional cycles. The Assembler is merely warning that the sequence of...

View Article


Image may be NSFW.
Clik here to view.

Synchronization issue of multiple ADE7913

Hi, I have an issue with synchronization of 3x ADE7913. I use uC with SPI clocks 6 MHz or 3 MHz. I can't use 6 MHz SPI clocks due to ADE7913 has 5.6 MHz SCLK limit. So I use 3 MHz for SCLK. When 3x...

View Article


Re: SPORT delay

Hi again Harshit and Jithul, I have now finished the first prototype implementing all necessary hardware and software for my data acquisition chain. It is surprisingly fast! Thanks again for your help....

View Article

Image may be NSFW.
Clik here to view.

Re: AD5933 and AD5934 evaluation board software commands

thanks a lot. only a question about the program itself and the export: after the measuremtn i only get the "impedance" not "real/imaginary" part.is there an option to enable it?

View Article

Re: AD5933 and AD5934 evaluation board software commands

Hi Ruben, the source code is available in the ftp site.. you can open and tweak it. Best Regards,Miguel

View Article

Re: Using SD card in BF609 through bare metal programming

Hi, As your question specifically relates to the BF60x, I have moved it from the "Processors and DSP" community to the ADSP-BF60x community. I notice, also, that you submitted the same query through...

View Article


Re: Output 3D Frame packing in progressive format

Hi, Thanks for your quick reply.I have two questions:- Can you confirm it is possible?- What do you mean with "little involved"? Is it a little adjustment or is it very difficult to achieve? Just to...

View Article

Re: how to enable the IwIP stack in ADSP BF 527 via Cross core embedded...

Hi, We have a port of the lwIP stack for both VisualDSP++ and CrossCore Embedded Studio, and on the BF527 I am not aware of any reliability issues in either. Within VisualDSP++, lwIP can be added to a...

View Article


Image may be NSFW.
Clik here to view.

Re: 2015080- Anveshan 2014

Sorry i m new to this community. Thanks:)

View Article

Re: Upgrading FMCOMMS2 Vivado design to Vivado 2014.2

I have been able to get the design to work in Vivado 2014.2 and 2014.3.  The main key was that when upgrading to 2014.2, I had to add the line "set_property -dict [list CONFIG.C_AUX_RESET_HIGH {0}]...

View Article


Re: SDR: Communication over the air using fmcomms1 and zedboard

Thanks for the reply. I want these two boards of FMCOMMS1 can communicate to each other (synchronized)  over the air. I have found one of the resources that use matlab, Support Package Hardware Setup -...

View Article

Re: ADE7953: Can't get OverVoltage IRQ working

Hi Pierre-Emmanuel, It sounds like the SAGCYC, SAGLVL and OVLVL registers are set correctly but that maybe the IRQENA is not. Double check your settings:SAGCYC, SAGLVL and OVLVL, what are your settings...

View Article

HMC89x tunable filter recommended driver circuit

What is the recommended circuitry for driving the control voltages of the HMC89x family of tunable filters?

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>