Re: ADV7850 Output HDCP
Mainly I used scripts to get a picture on screen, and then I set manually the the HDCP_ENABLE(B8 AF[7]), FRAME_ENC(B8 AF[4]), and the EXT_HDMI_MODE(B8 AF[1]) registers.The script package version is...
View ArticleRe: AD8400-1KOhm For PT100 Simulation
Hi Mark, Yes there is a Cortex M0 Family processor involved in my project, it is used to compute some operation and give out the right resistor value by setting the value via SPI. I've implemented a...
View ArticleRe: Looking for OPA with voltage limiting function
I also have to consider the OPA698. Regarding the AD8036, I started playing with the Spice model (using LTSpice) and I am a bit surprised. I simulated a non-inverting amplifier with a gain of 1, just...
View ArticleClik here to view.
Re: AD8400-1KOhm For PT100 Simulation
Hi David, 1.)I see your reason why you use 2 potentiometers in parallel: OK.2.)I reckon the accuracy of your measuring devices are too bad.Just consider the direct Ohm measuring of the AD8400...
View ArticleClik here to view.
Re: AD9912 I use spur killer, I need killed spur harmonic 2, It should write...
LouijieC написал(а): It was described in the data sheet that 4 LSB's is enough to create an output which approximately 60 dB below the full scale DAC code. In your case the value of 0x0501 would be...
View ArticleRe: ADE7913 for DC sensor measurement
Hi hmani,Thanks for your response.I may think that ADE7913/7912 is made for 3 phase meter application. If we want to use that to monitor current, we can use low side sense current method following a...
View ArticleRe: ADV8005 OSD Function-We need Technical support
Dear，Using ADV 8005 EBZ，How to request ADV8005 EVB Schematics OrCAD files？
View ArticleRe: ADN4665 enable inputs truth table
Hello, Inside of the ADN4665 there is an OR gate for enabling the outputs.You are right, the truth table (Table 5.) is not completely correct.Pulling EN# low OR pulling EN high will enable the outputs...
View ArticleRe: ADI Linux version that works with FMCOMMS2 Vivado 2013.4 on ZedBoard
Lars My apologies for not responding. Was off this topic due to other priorities. For the record, my problem was due to some stale generated files. Once I rechecked out everything fresh, it worked. It...
View ArticleWhy this program can't receive the right data?
Hi friends, I write a program to realize point to point communication, now I just do it on one board, the txbuf's datas is right, but the receive buf can't achieve the datas from the txbuf. Do...
View ArticleRe: Parameters in no-os for FMCOMMS2!
Hi Jetmir, rx_data_clock_delay and rx_data_delay settings affect the DATA_CLK and the Rx Data delays. If the two values are equal, then the data bits will approximately align with the DATA_CLK edge.For...
View ArticleRe: CC3089 error while building hough transform code in BF609 EZ KIT
Hi, Please open the system.svc file, and check there are no errors reported against installed Add-In versions. If there aren't, please provide a copy of the project you are trying to build, along with...
View ArticleRe: Display a frame on monitor from ADSP BF609 EZ kit..
Hi, I am aware of customers having ported OpenCV to run on their Blackfin targets, however we do not provide a port of this library. We do, however, have an Image Processing Toolbox software module...
View ArticleClik here to view.
FMCOMMS2 Vivado 2013.4 build works, but not quite right.
Was able to rebuild the FMCOMMS2 reference design with Vivado 2013.4 (64bit on Ubuntu 14.04), successfully and use with IIOScope and LINUX, but for a this problem. The RX1 ADC channel seems to have...
View ArticleRe: ADV7181D 12bit RGB DDR mode
Hello, Thank you for your advice. I will confirmt it. I would like to ask one more question.Could you give me your advicew whethere description of datasheet table 53 includes wrong description or not...
View ArticleUsing ADXRS453BEYZ (LCC_V package) on EVAL-ADXRS453Z-M
Hi, Only one simple question. Could ADXRS453BEYZ in LLC_V be used on EVAL-ADXRS453Z-M? Or only ADXRS453BRGZ in SOIC_CAV? Regards,Ivan
View ArticleRe: CC3089 error while building hough transform code in BF609 EZ KIT
HiI've upgraded Blackfin 2D Graphics Library v 3.3.0 to 4.0.0. Did clean, and built up using the upgraded add-ins and now I'm facing cc3089 error and make error. What I've observed is my CCES version...
View ArticleRe: Using ADXRS453BEYZ (LCC_V package) on EVAL-ADXRS453Z-M
Hi Ivan, The socket on EVAL-ADXRS453Z-M can only support SOIC package. BRNeil
View ArticleRe: Using ADXRS453BEYZ (LCC_V package) on EVAL-ADXRS453Z-M
Hi Neil, Thank you for the fast reply. Regards,Ivan
View ArticleRe: Is there any method that ADV7181D does not output AV code(EAV/SAV) on the...
Hello, Thank you for your reply. In this case, input is CVBS(NTSC-J) 480i with SDP and output is YCbCr 16bit.HS/VS/FIELD pins are used. (SAV/EAV is not used.)When output is 16 bit, even if we use SDP...
View Article