Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

How to set the TDD status from Tx to Rx or to other status in IIO?

Hello,I want to test the TDD mode in IIO Oscilloscope. And I open the FMComms2 Advanced window, there is a selection TDD. If I check the TDD, how to set the status Rx and Tx? What is the meaning of the...

View Article


Re: EVAL-ADT7x20EBZ Evaluation Software Error

Hello Lluis, thank you for looking into this.  The customer has now tested the proposed procedure. His computer did not automatically find any SW or drivers(he is an admin user and has full access to...

View Article


Re: ADV7626 CSC error, error rate: 1%

Hi Douglas, Any update from your side for the previous question from my side? Best Regards,Jeyasudha.M

View Article

Re: ADV7181 FTP: How can I get the password ?

Handled offline.

View Article

Re: Potential bug in dc_filter?

Hi Andy,  I've rechecked the dc_filter, and I think you missed a few things, like :dcfilt_offset - should be a 2's complement number, and it should use for known constant DC offsetdcfilt_coeff - will...

View Article


Re: EVAL-ADUSB2EBZ (USBi) support under Linux?

Hi Lars - I appreciate you making the effort to at least start the process of seeing what can be released and/or documented. ADI has been nice enough to release the board schematic for the USBi but...

View Article

AD9824 - CCD clamping operation

I am currently working on a CCD based product that uses the AD9824 to digitise the CCD output. On the whole it works very well, but we have been experiencing occasional (approx 1 in 500) images where...

View Article

Re: Failed to read a ADV7282-M register

Hi, If the I2C writes are operating correctly, it is possible that this is an I2C read issue only.Our video decoder products use a repeated start when carrying out I2C read transactions. An additional...

View Article


Re: AD5755 unusual behavior for the 1st channel

Hi Mark, Please find the clarifications below, Let me consider the voltage output DAC only The FAULT bit for the Vout_A is set, after channel A is enabledThere is a difference between channelA and the...

View Article


Image may be NSFW.
Clik here to view.

Re: ADV7282-M output parameter validation

Hi , VBI - is the vertical blanking Interval  ( non-active region)The full video data is transmitted from ADV7282-M.This is the full video lines 525 lines - ( 480 active lines  and 45 blanking lines)....

View Article

Re: AD21489 I2C NACK handling

Hi Frank, What is the value of the TWIMSTAT register when you do a TWI write with a bad slave address ?You may have to Write 1 to clear the TWIANAK bit Regards,Mahesh

View Article

Re: Problems with SPI slave boot on ADSP-21479

Hi Chris, The default setting of SPICTL register during SPI Slave Boot is 0x4d22 and the MSBF bit is cleared.So it is LSB first. But the Host is sending data in MSB first format.Hence you have to send...

View Article

Re: ADV7181C Analog RGB

Dear dave, Thanks for your reply there is any setting i can do to decode 768 x 576 pixel 625i RGB  on ADV7181 chip.Please Suggest us regrading 768 x 576 pixel 625i RGB decode.there any other devices...

View Article


Re: ADV7181c

Dear GuenterL, Thanks for your reply My Analog RGB input is 768 x 576 625i. i couldn't  how to set to this pixel input decodeCan you help me with this Thanking youRegards,Balaji

View Article

Re: Flash programming in ADSP21489

Dear Sir,  In our design, we are using both ADSP21489 and Spartan FPGA to cater our application requirements. we proved the functionality of our design when both programs loaded through JTAGs. Now, I'm...

View Article


ADIS16209

I use ADIS16209 evaluation board with TI controller. I not set means not write any control register & assume that it is ok as per datasheet.1. My target is to measure X or Y axis both side with...

View Article

Pin Muxing in CCES 1.1.0 for ADSP-BF538F

Hi All, I am using the black fin processor ADSP-BF538F in one of our project. I am using the cross core embedded studio 1.1.0 IDE for my development. I followed the procedure to create a cross core...

View Article


ADRF6518 output noise, dBV/Hz or dBV/sqrt(Hz)

hi; I saw the output noise density of ADRF6158 is -104.6dBV/Hz, but the unit in datasheet of ADRF6516 is dBV/sqrt(Hz), what is the different between? or just a print error in datasheet of ADRF6518, it...

View Article

BF609: second wake-up issue with hibernate mode

We are working with the BF609 rev0.2, 2013 blackfin-bvuildroot.1-We are able to enable hibernate mode (echo mem > /sys/power/state)2-Wake-up done from CAN-RX3-We are able to able to run the second...

View Article

Image may be NSFW.
Clik here to view.

Re: Question about the ADV7180 with the output picture shake

Dear GuenterL        The video source is the Camera. and there is no anti-aliasing filtering in front of the ADV7180 inputs.        which signal should I to test when debuging the circuit?     

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>