Re: ADIS16480 Register Writes to PAGE_ID 0x03 problems
I think that I would have the same thoughts that you do because by itself, moving from page 2 to page 3 doesn't do anything different, other than access a different page in the RAM. Any chance you can...
View ArticleRe: Sort an array - find the best way!
Hi LuigiDiPalo,Have you considered merge sort? There are c code for merge sort readily available on web. Using "merge sort c code" can find them. For your case, you may need to modify the c code, which...
View ArticleNo-OS driver for updated axi_ad9361 core
I have managed to build the latest fpgahdl_xilinx PL from the Dec.13, 2013 drop for the FMCOMMS2 AD9361 system. I'm eager to try out the new code on my platform but discovered that the No-OS drivers do...
View ArticleRe: Can "ADV7511W" receive 1920x1080 60Hz interlace video with 8bit, pixel...
Hello, Thank you for your reply. Questoin 1: What we want to know is whether ADV7511W can receive 1920x1080 60Hz Interlace video (sampling clock 74.25MHz) with "8bit", pixel clock "148.5MHz". Can...
View ArticleRe: ADV7630 internal EDID issue
Hello, The entire readback of EDID content is shown below:0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x17,0x10,0x01,0x09,0x01,0x00,0x00,0x00,...
View ArticleRe: I need measure a signal with 5 microvolts peak-to-peak with AD620 it's...
There will not be a specification which directly tells the smallest signal which can be amplified by an IA. There are specifications for the amount of noise which the IA creates at the inputs. Then,...
View ArticleRe: Some questions for your good ADM2582E EMC trouble fixing
I got it.Thanks Richard Kaos
View ArticleClik here to view.
ADV7511_Programming_Guide
Dear Sir/Madam, We have a question about ADV7511_Programming_Guide.pdf.Pls refer to the Table 94 of Page 112.Address of top of BKSV12 is 0x60.However,we think that is 0x3C.Which is correct?. 0x60 RO...
View ArticleHow can I use ADV7619 with an internal EDID?
Hi all I use ADV7619 I can not Internal EDID Help ME...
View ArticleRe: ADAS3023 PGIA gain config
Hi, Larry. Only channels 0 and 1 of the ADAS3023 can be controlled independently. Lorime is right, you can try the ADAS3022. Using the ADAS3022's advanced sequencer mode (see page 39 of the ADAS3022...
View ArticleClik here to view.
Re: AD9643 - how do control the sampling rate?
Dear Harris: I have question when I used the AD9643 + ADC-HSC-EVALCZ ,1. Setup:HWUse AD9643 EVB + HSC-ADC-EVALCZ (FPGA)Use J506 default input path:Put C532, C533 0.1uF Cap.Remove the R541 &...
View ArticleADuM3221 Gate Pulldown Resistors
Hello,I am designing a circuit that uses the ADuM3221 to drive some MOSFET gates.Ordinarily I would include a 1M pulldown resistor on the gate pin so that the FET will be off until all the logic powers...
View ArticleRe: 3W Emergency Light
Chun, you may be able to use a comparator powered by the battery such as the ADCMP350http://www.analog.com/en/special-linear-functions/comparators/adcmp350/products/product.html you need to rectify the...
View ArticleTx Quadrature Calibration (Tx port output power)
During the Tx quadrature calibration, we have observed signals at high power level on the active Tx ports. I understand that we can control the Tx attenuation during Tx quadrature calibration by...
View ArticleRe: how do i decrease Iq with adp160
Michael, I am interested to know if the ADP160 you were testing was exposed to ligh. Look at this discussionhttp://ez.analog.com/message/34596#34596 It may be possible that exposure to ligh would also...
View ArticleRe: ADV7393 Output Video Scrolling Vertically
Hi All, Could you try the following I2C write instead of writting 0x0C to register 8A: 54 8A 04 ; SD Timing Mode 2 Could you also forward a 'scope snapshot of the HS and VS syncs you are sending to...
View ArticleRe: Tx Quadrature Calibration (Tx port output power)
First thing I would check is whether Rx Quad cal tracking calibration is running simultaneously with Tx Quad cal.It needs to be off. You also should make sure that Tx quad cal test tones are placed...
View ArticleRe: AD9643 - how do control the sampling rate?
Hi Cien, I am just a little confused now. In one of your first posts you said that the evaluation board was working fine in the default configuration. Has something changed? Did you make sure to...
View ArticleRe: IMAGEON FMC ADV7611
Robin, Unfortunately I cannot use your binaries for the hardware design because I am using different hardware (Enclustra ZX3 with PM3). Perhaps I will try your kernel and rootfs in the future, however....
View ArticleRe: ADV7842 HDMI Incorrect Video Measurment
If the timing for those 2 resolutions are about the same then there is no way to differentiate between them. The only real difference is the blanking width which we don't measure. This is not the...
View Article