Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

need XML file for EVAL-ADV8003-SMZ-P

Matt,I am also unable to find the XML file needed for AVES3 to work with my EVAL-ADV8003-SMZ-P board. Could you post a link? Thanks

View Article


Re: ADV7610 setting file

Hello DaveD, Thank you for your advice.

View Article


Re: need XML file for EVAL-ADV8003-SMZ-P

Due to the complexity of this board, we were thinking it might be more user-friendly to use the SW driver rather than scripts to configure the board. I assume this kit included a remote control. Were...

View Article

Re: ADV7619 simultaneous operation

Can you provide more details on what you are trying to do? -Matt

View Article

Re: ADUC7020 eval. board software

Board Type : ADuC7020 Eval. Board Rev A2.  QuickStart Plus. I searched installed directory (ADuC7XXXV0.2) and (/Keil/Arm/Boards/ADI/ADuc702x), but I can't find board related source codes.When I power...

View Article


Re: bf609 eppi2 transmit data

have you completed it? if not ,you can try: change ENUM_EPPI_CTL_DLEN08 to ENUM_EPPI_CTL_DLEN16, Even if your hardware is in 8bit mode. i met the similar.

View Article

Re: ADV3221 IBIS model

Dear Jonathan Thank you very much for your quick answer. ADV3221 is analog device, so it needs SPICE model to simulate, I think too.But in this case, I would like to check only the transmission...

View Article

Can I use usb and ucfs in bf609_coreB?

HI, Can I use usb and ucfs in bf609_coreB? When I coreB added ucfs, will lead coreA error.TF card initialization and read-write file failed. I joined the two macros defined in the preprocessing :...

View Article


Re: demodulation sin o square wave?

You can use a sine wave but it it must have a minimum drive level (see Figure 22).  Even when you drive the LO input with a sine wave, that signal gets turned into a square wave inside the AD8333...

View Article


Re: Default setup of ADV7441A

Hello Dave, Thank you for making the time for my question.  Best regards,Kou

View Article

ADV7611 and ADV7610 Video format

Hello all, We can not find description of Quarter HD(960*540) about PRIM_MODE[3:0] VID_STD[5:0] in datasheet.If above can be supported. Please let me know how to do it. Regards,

View Article

ADV7611 free run mode

Hello all, When we set HDMI_FRUN_EN=1 and change to Free run,Cycle of HS and VS signal become unstable.After that, Cycle become stable.As the result of our check, 80ms is needed by stability of VS...

View Article

AD9777 overall delay

Hi I am using the AD9777 in an existing design of a digital feedback controller, so actual input-to-output time delay is critical. What is this delay for the AD9777? (the datasheet only gives the...

View Article


Re: Signal latancy in the ADV7181C and ADV7392.

For he combination of AD and Intersil, the pixel clock rate is 13.5 MHz (Since Intersil's serializer needs 13.5MHz clock rate). If I convert this into time it is 0.074us. You mentioned the delay in CP...

View Article

Re: [ADV7511W] HDMI v1.4a, HDCP v1.3.

Hello, Thank you very much for your reply.Please fix the typo of the datasheet. Thank you.Best regards.

View Article


USBi now for $80!!

Down from $185 I think...Is this a holiday promotion or stock clearance before the new programmer based on XMOS is introduced?

View Article

Re: ADV7619 simultaneous operation

Hello, I ask the question of ADV7619  dividing two thread.I wrote the detail below thread.http://ez.analog.com/message/125762#125762 We use two ADV7619 and we ask if ADV7619 support  4K2K@60p.Regards,

View Article


Re: ADV7182 analog input level

Mr. GuenterThanks again for your answers on this. I didn't mean to discuss about what resistor divider network will get what gain level of the input signal. I post our schematic design here. The...

View Article

Re: How to use Inter Core Communication on bf609?

Hi, Aaronwu I cloned the new git repository but there isn't linux kernel source code in the adi-buildroot-code/linux/linux-kernel. I tryed to copy the linux-kernle sorce code to...

View Article

Re: How to use Inter Core Communication on bf609?

Please run "git submodule update --init" as it says in http://docs.blackfin.uclinux.org/doku.php?id=buildroot:build-system:build_a_target

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>