What's the difference between synchronous burst mode and asynchronous mode of...
Your reply will be helpful for me. Thank you!
View ArticleRe: ADV7511 ZedBoard design with MicroBlaze instead of ARM Cortex-A9
I took a look at the ADV7511 Transmitter Library source code, but as Dragos mentioned, there are a number of functions that must be written by the user in wrapper.c. These include not just the basic...
View ArticleRe: DDS AD9852
Hi Wiotte Fabrice, Figure 59 of the AD9852 datasheet shows the supply current consumption of AD9852 for 2 configurations.Figure 60 shows current consumption by each four function:Control DACoutput...
View ArticleRe: AD9631 AUXDAC effects
It works in TDD mode. I think the reference clock is stabilized in temperature. These effects are repeatable. My question is that is this effect expected when only changing the value in register 0x18?
View ArticleRe: ADA4411-3 monochrome analog video input signal
Hello, Thank you for your advice. Regards,
View ArticleIRE at ADV7171 without pedestal setting
Hello all, Please let me know your advice the relationship between input signal and brightness described in datasheet P.13 DATA PATH DESCRIPTION.Question1 We think below. Is this correct ? Input 16:...
View ArticleClik here to view.
Re: Make a signal with a number of precise periods
Hi Mikael, Yes. For AD9851, you can issue frequency update (FQ_UD) to transfer data from buffer register to active register. Looking at the timing characteristics, the latency defines how many clock...
View ArticleQuery about ADL5530's Output
Hi, thereWe are giving a PECL output from a ECL D-flip flop (MC100EP31) to ADL5530 (RF Amplifier). The amplitude of the input PECL signal is 700mV and the working voltage of RF amplifier in their...
View ArticleClik here to view.
Re: AD7747-EBZ Programming in LabVIEW
I have been working on programming for a few days now. Just thought I would give you feedback on your assistance. This is a simple VI that can setup the AD7747 for calibration and run continuous...
View ArticleRe: Short Delay DDS
AD9910 can only produce sinusoidal outputs. You can introduce an additional circuitry at the output if you want to produce different kind of waveforms. Like if you want a square wave, you can add a...
View ArticleAbout ADG3241 Level shift IC
Hi there,I have a simple question about ADG3241, level shift IC.http://www.analog.com/static/imported-files/data_sheets/ADG3241.pdfI want the levelshift from 3.3V to 1.8V/2.5V.I checked out the...
View ArticleRe: ADV7511 ZedBoard design with MicroBlaze instead of ARM Cortex-A9
Reposting this here since my e-mail reply didn't get copied to the forum... I didn't use the timer interrupt at all. The ADV7511 demo seems to work without it. As far as I can tell, the timer is just...
View ArticleRe: ADV7511 ZedBoard design with MicroBlaze instead of ARM Cortex-A9
Missing fmc_iic_sw link: http://zedboard.org/sites/default/files/design/FMC_IMAGEON_Building_Video_Design_Tutorial_14_4_20130110.zip
View ArticleRe: AD9361 evaluation board with Xilinx evaluation board...
Hi, rgetz: Thank you very much for answer my questions, I think I understanding your answer and I hope you know my question's means. Best Regards, ADI_USERS
View ArticleADG2188 - I2C read protocol
I am attempting to us an I2C software package based on smbus read/write protocols. The write function works but the read function does not.I observe, using an I2C bus monitor, that an smbus read only...
View ArticleClik here to view.
Re: binary control
Hello Gennady, This would be a lot easier to do if SigmaStudio had a bit-test function as suggested by jon71 athttp://ez.analog.com/message/132542#132542Without that function, what would be...
View ArticleRe: noise of SSM2019
Dear Sir/Madam, I am still waiting for your reply,would appreciate it if you could expedite your response to us. Thank you. Sincerely yours,Kou
View ArticleCan I use the ADE7757 (AD71056) to measure AC line current?
I have a customer who wants to measure the AC line current into his device. The input is standard 120V, single phase AC. They require isolation and 2% accuracy. This is a sub metering application....
View ArticleRe: binary control
Thanks a lot, Bob.You are right, this is a mess.I was thinking about switching multiplexers with one byte, masking bits when switching is disabled.Seems like it will be a lot easier to switch index...
View ArticleRe: AD7689 VDD Power supply
Thanks, Maithil. >>The VREF on the page 13 and 14 referes to the external reference.So when using internal reference, I should not refer to graph on page 13 and 14?ADI recommends to connect over...
View Article