Re: typo? of XPE power estimation
Thanks for spotting this - we will get it updated for the next version of this document Regards Tim
View ArticleRe: No compressed audio (AC3, DD+ and DTS) from Eval-ADV7612-ADV7511p board
Hi Madhan, Use the software driver (1.55RC2) to configure the board rather than trying to configure with AVES (scripts). The software driver will output over RS232 (115200,8,N,1) and accept commands...
View ArticleRe: AD9361 Receive RF Rx phase delay shift
Hi,I understand that there is digital delay. In order to implement QPSK I need to synchronize the phase of the Rx path, so I thought of sending sine wave training sequence from the transmitter and to...
View ArticleRe: AD9361 Receive RF Rx phase delay shift
oops,I meant I understand that there is no digital delay.
View ArticleRe: AD9144 FMC and FMC DAQ2 for ADS7-V1 or other Xilinx FPGA
charlyelkhoury, do you have any board modification ideas that you can provide? I'm willing to break a couple of these if I have to.
View ArticleClik here to view.
Re: AD9361 Linux kernel compatible with 3.14.0?
I gave up trying to get the 9361 working with an internal 3.14 kernel around last November and switched over to a 3.17-ish Analog Devices kernel. (I had to pull in the AXI DMA driver from the Xilinx...
View ArticleHMC1048 Port Matching
I am looking for some S-parameter files for the RF and LO ports of the HMC1048LC3B part. On many of the other mixers they are readily available from the product page but seem to be missing on this...
View ArticleRe: AD9364 RX baseband analog filter passband response is not flat
Pete: That's expected - the RF bandwidth will drop ~1dB in the passband. Check out:http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/software/filters for a description & solution...
View ArticleHI - shark -213749 GPIO interrupt c source code
HI, i need c source code for GPIO interrupt for SHARK-213749 Thanking you,
View ArticleRe: AD8657ARMZ latch-up phenomena
AT, The designer said a customer noticed an anomaly a few years ago and sent me an email he had sent to the product line apps engineer. Excerpts: "...This is a capacitive feed through problem....
View ArticleRe: Signal generator with a PLL integrated VCO
Can you use 2 parts? 2 ADF4351 evaluation boards would do what you're trying to do. If you want much narrower than 10 kHz spacing, try the 2 ADF4355-2 boards. ADF4351:...
View ArticleLevel Translator ADG3308
Hi, I am using the ADG3808 in my design. For the VCCA I am applying 1.5V supply and for the VCCY I am feeding 3.3V supply. In my system Both 3.3V and 1.5V powered up simultaneously. Whether it will be...
View ArticleAD9361 NO-OS driver: BBPLL calibration timeout?
Hi, I am using AD9361 NO-OS driver (from 2014_R2). I only need to control AD9361 via SPI bus so I use platform_generic. I compiled the driver and tried on my board. After ad9361_bbpll_set_rate(), I...
View ArticleRe: ADV7610 480p Color Issue
Hi Matt- I'm trying to reproduce the same settings, but I don't know what any of the values going to address 72 are: 72 01 00 ; Set N Value(6144)72 02 18 ; Set N Value(6144)72 03 00 ; Set N...
View ArticleClik here to view.
Re: ADE7758 | Issue reading WFORM register
Thank you very much for your assistance, Dlath & Hmani! Best regardsMathias
View ArticleRe: Highest rate possible for 20-24 bit resolution and high noise
Moving your inquiry to the Precision ADC community for discussion of 20-24 bit sampling requirements and limitations.
View ArticleRe: ADV7610 480p Color Issue
I received the EVAL-ADV7610EBZ today. I verified that it was detected by Windows 7 64-bit and correct drivers loaded. Then I ran the following script and verified that it received/transmitted...
View ArticleRe: ADF4110 RF Sensitivity Over Temperature
Your data is correct. More detailed data attached.
View Article