Re: Interfacing AD7764
Hi MClifford, Thanks for your reply. >> FSI signal - Clock this relative to the SCLK that you receive from the ADC "SCO".Do I need to tap the SCO to MCU Interrupt also to sync FSI signal wrt SCO...
View ArticleRe: ADE7816: Peak detection
I've never fully understood how the IPEAK stuff works on a 7816. As an experiment, with 50Hz ideal inputs on V and I, I've left the CHANNEL_SEL bit at its default of 0 so I'm monitoring channels A, B...
View ArticleRe: TCPIP1940 protocol specification
After more investigation with a TCP server in debug mode, I have found that the packets are far less cryptic than I thought first (the problem with Wireshark is to find *all* packets containing data......
View ArticleRe: Can ADL5391 ENBL pin drived by MCU ?
Thanks.I have a question.When ADL5391 work, it was very very heat,that is the chip temperature is very high. It is normal?What can I do with that can improve it?
View ArticleRe: interfacing AD9144-ADRF6720-EBZ to FPGA
You can use that interposer but you also need JESD204 licensed ip core from Xilinx to work with them.
View ArticleClik here to view.
Re: Can ADL5391 ENBL pin drived by MCU ?
Thanks.I have a question.When ADL5391 work, it was very very heat,that is the chip temperature is very high. It is normal?What can I do with that can improve it?
View ArticleI am not able to find the Camera EI3 Extender Board Support Package 1.0.1....
I have installed the CCES 1.1.0 evaluation license version for ADSP BF609 EZ-KIT-1.0. I required the "Camera E13 extended board support package(BSP)" to use those the Sensor (MT9M114) driver with EZ...
View ArticleClik here to view.
Re: interfacing AD9144-ADRF6720-EBZ to FPGA
Thanks Neo for mentioning the required Xillinx licenseI am still looking at layouts/schematic/pictures and the Z-Pack hm-zd connector on the this EBZ evaluation board seems to mate with the JESD204x...
View ArticleClik here to view.
AD-FMCCOMMS1 always cuts sampling frequency in half?
Hello,I am trying to transmit a wideband IQ signal with AD-FMCCOMMS1+Zedboard.Using the reference image on AD-FMCOMMS1-EBZ User Guide [Analog Devices Wiki], and iio-oscilloscope,the DAC sampling rate...
View ArticleRe: LET threshold for AD8561S?
HARRY,CHDJ75 ASKED ABOUT SINGLE EVENT EFFECTS LATCHUP RADIATION HARDNESS. I HAVE THE SAME QUESTION. DID ADI OR A 3RD PARTY PERFORM SEL/SET TESTS ON THE AD8561S AND HOW MANY MEV*CM**2/MG IS IT RATED FOR?
View ArticleRe: ADP5054 ADISimPower Tool
Dear Kevin:I already to download the ADP5054 ADISimPower at ADI Website. Another I would like to refer to ADP5054 EVB Board PCB Layout, can you provide Gerber file to me a reference? Thanks~ My...
View ArticleRe: Dynamic bass boost in a 2.1 stereo design
Hi Bob, Thanks for the information! I wonder if there is any graphical description of the gain that is applied by the dynamic bass bost (gain vs frequency)? For example: Settings:Boos Freq = 45HzBoost...
View ArticleRe: RMS+PEAK Combo - noise problems ...
Hi Brett, I could not find out how to start a new discussion but I send the question directly to you :-)! I wonder if there is any description or"curve" of the gain that is applied by the dynamic bass...
View ArticleHMC980LP4E Powering 4 TGA2598-SM
Hi I am using the HMC980LP4E to power 4 TGA2598-SM on a single board.The design is attached and it would very appreciate your review and recommendations. Thanks a lot.
View ArticleClik here to view.
4K HDMI Receiver and transmitter
Dear Supporter 1. According to the ADV7619 , when the HDMI input is 4K , the TTL output may be at YCrCb 4:2:2 format, 12 bits as following: When setting OP_FORMAT_SEL[7:0] = 0x96Can you give a clear...
View ArticleClik here to view.
ADV7511 output Video format
Hi, I am using a ADV7611 ,ADV7511 and FPGA.My system get a HDMI Input at a Desktop comupter, and put a HDMI output to a Oculus Rift DK2. PC---->ADV7611(HDMI...
View ArticleRe: FMCADC2 - Clock Speed
Changing converter clock speeds, means changing JESD204B rates. This in turn means re-compiling the Xilinx designs, since they set the clock rates of their JESD204B core at compile/synthesis time. -...
View ArticleRe: ADV7842 multiburst response issue
Hi, Can you please advise on the following questions to ensure we understand your application/query correctly... You are using an ADI evaluation board to test this .e.g. EVAL-ADV7842-7511?You are...
View ArticleRe: AD9364 Digital Tuning Necessary?
Tom; Did you check out the link I provided? I think it answers these questions. If you don't think so, I can try to add more to the docs. - Robin
View Article