Re: ADV7611 DVI Input synchronization detection problem
Matt, I've got the serial port up and running. Here is the version information you requested:******************************************************************** ADI HDMI Repeater Application Ver R1.5...
View ArticleRe: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
The next step would be to generate an IP core from the qpsk model and insert that into the Vivado HDL reference design. It is also important to decide if you planning to use the ADI Linux platform for...
View ArticleRe: ADV7630: How to TMDS PLL reset
Hi aimPoint, So the video is transmitted correctly when you configure the EVAL-ADV7630EBZ with scripts but it is not transmitted when you configure EVAL-ADV7630EBZ with the latest software driver. Is...
View ArticleRe: ADV7842 composite and S-Video
So as I understand it you want a system with 3 BNC connectors and want to be able to handle CVBS, YC and YPbPr I would connect YPrPb to Ain1, 2, 3 or Ain4, 5, 6 inputs respectively. CVBS would use the...
View ArticleClik here to view.
Re: Communication system toolbox hardware support package for xilinx zynq...
Shobi, Unfortunately, we (ADI) do not have the zip file for this support package. The file xilinxzynqbasedradio.mlpkginstall is the right one to start with, and this is how we installed the support...
View ArticleClik here to view.
Re: Reprogramming FPGA XILINX VIRTEX 4, ADC AD9650 Eval board interface
Hi Mehdi, The FPGA source code for the default AD9650/HSC-ADC-EVALCZ evaluation setup is posted to our public ftp site at: ftp://ftp.analog.com/pub/HSSP_SW/fpga/The code is provided as-is per: This is...
View ArticleRe: Communication system toolbox hardware support package for xilinx zynq...
Hello sirThank you for your reply..I got that hardware support package sir..thank u
View ArticleRe: AD524 instrumentation amplifier giving different voltage values depending...
Sure. You have one "ground" for the resistor, and one for InAmp. Putting a voltmeteracross the resistor assumes ground is the bottom of the resistor, but the InAmp hasa different ground. Also, where...
View ArticleRe: ADAU1442 + AD1938 ADC Noise
Hello Fernando, I had similar noise in a mixer design, which turned out to have several causes as described at https://ez.analog.com/message/169919#169919Perhaps reading through this...
View ArticleAD7195 unable to rail?
The AD7195 within the system has been initialized: 48 1's written to the device, the configuration has been written with 0x000347, and the mode has been written with 0x180060. Purposefully setting the...
View ArticleRe: Lower Limit of Input Voltage for AD1939
Thanks a lot Dave. I understand it perfectly. I have one last query regarding the processing of the samples from AD1939 via DMA in the receiver buffer of the SPORT used in my ADSP-21489 SHARC...
View ArticleBF533: Retain memory contents after restart
Hi all, I am working on a project with a BF533 and I have a little problem that I hope you can help me with. So I have created an init code as described in EE-240, a booloader dxe and my_application...
View ArticleRe: Register for TMDS polarity ADV7850
Hello, I'll ask an expert on that part to come comment. Dave
View ArticleClik here to view.
Re: Changing the ADV7611 resolution after connecting the video source
Yep.. there is a delay that you can set for it asserts though. I think it defaults to 1 second. Dave
View ArticleRe: ADP5090 EVB question
Hi, Firstly, you need to mak sure the input power bigger than output power considering the efficiency. (Pin=Vin*Vin/4/R)Secondly, there is a OCV detecting time around 300ms when the ADP5090 can't...
View ArticleConnection from ADuCM360 to the ADT7410 via the I2C interface.
AN-1250 Rev 0, page 5 table 4 mentions .c and .h files for connection from the ADuCM360 to the ADT7410 via the I2C interface. Where to obtain these files? The same Application Note mentions on page 1...
View ArticleRe: Connection from ADuCM360 to the ADT7410 via the I2C interface.
Thank you for highlighting this - we will at least make sure you get the code here on EZ ASAP.
View ArticleInterfacing ARM and AD8403(Digital Potentiometer)
Dear sir/mam, As i am working interfacing ARM and AD8403 IC(digital potentiometer),i am measure resistance value,what i am doing is from ARM i am sending data through SPI every 20sec data i am...
View ArticleRe: Zedboard FMCOMMS2 SD Card Image
Austin: All the release files are:http://wiki.analog.com/resources/tools-software/linux-software/zynq_images -Robin
View Article