Eliminating AD9361 TX Carrier Output DC Output?
Hi, I am currently using an FMCOMM3/Zedboard platform to Transmit a modulated signal at max power (zero attenuation), but when I stop sending I/Q modulation data I would like to minimize the TX output...
View ArticleRe: Suitable Driver for AD9681 ADC, ADL5566 or AD8351 or else?
Hi Jim,Thanks for your reply - however, these facts I can read from the ADL5566 datasheet and as mentioned we have been using said device for two years now. I am more looking for experience reports on...
View ArticleRe: Suitable Driver for AD9681 ADC, ADL5566 or AD8351 or else?
correction for above: I found the input impedances (AD9681 datasheet and product info | Octal, 14-Bit, 125 MSPS, Serial LVDS, 1.8 V Analog-to-Digital Converter | Analog to …) My general questions...
View ArticleADUC 7061 - problem in interrupt handling
hi i'am using keil uvision 3 IDE ,in evaluation mode , i'am just trying a external interrupt 0 with a ADUC 7061 mnikit .A key (push button) has connected to the External interrupt pin 0 ,...
View ArticleRe: ADA4091-2
Hello Kris, The voltage mentioned above is my system supply voltage which is within the range of 18v voltage range is 17.94v ~ 18.06v and 20v voltage range is 18.88v ~ 18.98v. My application is...
View ArticleClik here to view.
Re: ADF4158 FSK Settings
Thank you very much for your prompt reply. I will try the .txt setting file on the evaluation board later. Thanks again.
View ArticleRe: How can I solve analog input amplitude shift and saturation in AD7606?
Thank you for answer I solve the problemsI didn't connect VxGND to AGND...TTAfter, I connect VxGND to AGND, voltage shift and saturation problems were solvedAnd, I used AD7606-4.... I thought it is...
View ArticleRe: UART TTL connection between ADUC 836 and display
no i can't!!!!!.....now WSD after 2 attempts give the error4!
View ArticleSSM2804 - ALC and H/W Limiter, both available on the HP L-R outputs ?
Hi, I am considering using this IC for a new audio accessory due to its inclusion of the adjustable head-phone limiter and ALC compression.I need confirmation of some details that don't seem to be...
View ArticleRe: Question for your IIO Oscilloscope
Hi, It is LSBs. E.g. if the converter is a 12bit converter and the value is signed it will go from -2048 to 2047. - Lars
View ArticleRe: AD9238 ADC Voltage Input
Hi - The AD9706 output is a current. The voltage at the output pins should be +/- 0.8V relative to OTCM. Thanks,Larry
View ArticleRe: HMC598 Die
Please apply an input signal and let me know if it continues to be high.
View ArticleRe: HMC783LP6CE serial port write operation
The evaluation kit is plug and play. You shouldn't need to do anything special to write to the HMC783LP6CE.
View ArticleRe: HMC783LP6CE serial port write operation
I want to replicate the USB interface to control the HMC783LP6CE using the evaluation kit of ft2232d (DPL-2232PB). I need to know if the Fast Opto-Isolated Serial Interface mode is the correct mode to...
View ArticleRe: ADE7878 HSDC samples
Hi hmani, I am applying FFT algorithm to the HSDC port samples.As you said, I have read the ANGLEx registers, before and after turning on the integrator, and their values were the same I told you...
View ArticleClik here to view.
Re: Detail Manual for your "IIO Oscilloscope"
Hi, This problem can be ignored it's a issue with the test pattern checker, the chip itself works fine. - Lars
View ArticleRe: AD-FMCOMMS3-EBZ Quick Start Reference Design for VC707
FMCOMMS2 and FMCOMMS3 are SW- and HDL-wise identical.See instructions here: http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/quickstart/microblaze The kernel and bitstream is all build...
View ArticleWhat type of ADC amp front end is better soultion
Hi All I am designing a front end for an Audio A2D who required differential input from a single ended source, I am considering 2 approach for the front end :the first approach is to use a discrete 3...
View ArticleRe: AD9364 RF DC Offset
Hi Luferchik, Can you please try to use our unmodified design and tell us if the behavior is the same? Please note that the current HDL project (Commits · analogdevicesinc/hdl · GitHub) is now...
View ArticleRe: Sine wave in No-os driver FMcomms1-ebz
Vibhooti, Yes, Vivado 2014.2 is required. Regards,Dragos
View Article