Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: Why PAL Video work good but RGsB Video does not?

I was checked output voltage and it is bigger than video standard voltage but it did not have problem so I did not want to small it. Figure 5 ?what is the meaning of TNT?

View Article


Re: Sine wave in No-os driver FMcomms1-ebz

Where will I find its user doc ? is this ithttp://www.analog.com/static/imported-files/overviews/FMC-Communications_Product_Highlight.pdfHowever i got following code in...

View Article


Re: adv7604 custom res 1280 x 960

Hi Michael, The Free run line length = crystal clock/HFreq. The crystal clock = 28.636363 MHzThe input is progressive, so need to set the interlace bit to 0. This is at CP Map, 0x91[6]. There is a...

View Article

AD9914 no-dwell operation

Hello, I am programming the DDS to operate in no-dwell high and no-dwell low mode, i.e. continously ramping up and down. I was wondering if I should expect any clock cycles between each ramp? Figure 38...

View Article

Re: AD7190 huge power on settling time

Hi Jonathan, Thanks for the link to the document about the evaluation board. And sorry for the long time between my responses, but this is sort of a side project of mine, and I’ve been quite busy for...

View Article


Image may be NSFW.
Clik here to view.

Re: Details on ADA4870 Power CFB

I don’t think we would provide much more in the way of details.  I think maybe it is already understood that the output stage is a push pull follower, the input stage is CFB input stage design.    

View Article

How to find an Engineer/Developer

Hello, I've been working on a project for some time now with the ADV7612 chip and am having a heck of a time getting it working.  How do I connect with a contractor knowledgeable in this dept so that I...

View Article

Re: Programming ad5752 in 2s comp mode

Hi Mark, I managed to get the DAC working. The output is set to -+5v but only getting a max of -+2.2v. Does the reference pin 17 neeed to be hard wired to something? Many thanks for all these helps....

View Article


Re: How to find an Engineer/Developer

Normally we would recommend starting from one of our evaluation reference boards and using the supplied scripts to configure the board. Read First: Design Support Files OverviewAdvantiv™...

View Article


Image may be NSFW.
Clik here to view.

ADCMP582 Comparator: Disable Latch Feature.

In the Rev A data sheet for the ADCMP582, there is a figure that illustrates a method for disabling the latch feature.Here's the figure:I plan to use this device with Vcco=+3.3V.The LE pin is shown...

View Article

ADIS16209 ADIS16210- clarifications needed

  Dear Supporter need some clarifications regarding ADIS16209 and ADIS16210: "Both units ADIS16209  and ADIS 16210 state something which they call "Relative Accuracy" of +/- 0.1 deg.It is not clear...

View Article

Re: ADIS16209 ADIS16210- clarifications needed

"Both units ADIS16209 and ADIS 16210 state something which they call "Relative Accuracy" of +/- 0.1 deg.It is not clear what that means: accuracy relative to what? I guess this brings us back to the...

View Article

Re: ADIS16334 old evaluation board

Hi NevadaMarkThank you for your support. I found another ADISUSB and ADIS16334 set, and that worked with IMU_6DOF_2.(I downloaded "IMU_6DOF_2" 2years ago.)It might be hardware problem, I think.I'm...

View Article


Re: ADIS16334 old evaluation board

Hi Moto, I am sorry but this isn't clear to me. Do you have anything working, right now? But one more trouble came up.I tried "IMU_6DOF_3", then Loop read is ok, but Dialog control comes up the error...

View Article

Re: Accelerometer?

Were you able to find something that is suitable for your needs? 

View Article


Image may be NSFW.
Clik here to view.

ADE7878 HSDC samples

Hi, I have configured it to acquire samples from ADE7878 using HSDC port. We have developed our own RMS and phase calculus with these samples. The current sensors are rogowski sensors.The phase...

View Article

AD5933 Re/Im wrong signs

Hi I ported my code that works perfectly with the AD5933 EVM to Arduino Uno(16bit).I'm no longer using the EVM instead I'm using AD5933 chip with a custom board.The board seems to function correctly. I...

View Article


Re: AD9364 overvoltage protectoin RF inputs

It is typically done using limiter diodes.

View Article

Re: Where can I get the registers' configuration process of AD9361 from none...

Only API driver based applications are supported on Engineer Zone due to the number of registers and complexity.

View Article

Re: ADV7604 - Unstable hsync on output pixel port

I've sent the information off to the ADV7604 expert on this part.  Have you ever sent me the schematic and layout?  I've searched my emails and can't find it.  We can take it off line you you need to.

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>