Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Re: using AD8067 as inverting amplifier

Hi Niloy, As i read through the datasheet (page 13), I found out the error in your circuit is the value for feedback resistor. 1kohm is recommended as feedback rather than 10kohm.In your case, you can...

View Article


bootng zynq zc702+fmcomms5

Hi , I erased my SD card and loaded the unzipped image in the Zynq quick start page using the win32diskimager application.I then followed the rest of the instructions, including the boot & tools...

View Article


AD603 Data Sheet Circuit - Figure 49, page 18

Hello: I am making an amateur radio transceiver.  I have based the IF strip of the receiver section of the transceiver on the circuit shown in the data sheet page 18 (figure 49).  My circuit is as...

View Article

Image may be NSFW.
Clik here to view.

Re: Sigma300 (ADAU145x) Q&A

    Hello,     The Limiter block behaves similarly for me:Its "Flag" output is actually the Ratio output (thus is all over the place)Presumably, then, the "Ratio" output is the Flag -- but it's dead....

View Article

Re: AD9467

Thanks for a great answer,  i think i was confused about the timing diagram on figure 2 on page 7 before, but i makes more sense now.  One last question. The 2 output bits on each differential pair, do...

View Article


Image may be NSFW.
Clik here to view.

Re: Sigma300 (ADAU145x) Q&A

Bob, You are the best. Your test is much appreciated.It's really strange though. Which SigmaStudio version are you using?I'm running 3.11 Build 2, Rev 1396 (9/8/2014) and the limiter does not limit at...

View Article

adis 16364 gyro read problem

hello,i have an adis 16364 imu.when i read the product id everything works correctly.however,when i am trying to read the x_gyro_out for example the values i get are something...

View Article

Re: AD9361 sample rate in reference design

Hi DragosB First , I would like to thank you for your reply after which I am gradually able to understand the working . As you mentioned in your first reply to me the tx path frequencies are set in the...

View Article


Re: AD9625 2.5GSPS Simulation

Thank you very much Ian!

View Article


ADSP-21479 Software reset

Hi, In order to be able to implement a firmware-upgrade system, I'm trying to get the DSP to reboot and reload the application firmware from SPI NOR flash. From what I've gathered, writing the SRST bit...

View Article

Re: ADF4153 N DIVIDER OUTPUT from MUX

Hi Brigid-san, Thank you for your quick reply. I will talk to my customer with your comments. Best Regards,Ricky

View Article

Re: EVAL-AD7173-8SDZ firmware

Hi RobK-san, Thank you for your support.My customer reported me that he  confirmed the AD7173-8 operation in his circuit board.Thank you gain for your help. Best Regards,Ricky,

View Article

Re: BF609 uClinux booting fails

Hi Jeremy, please start a new thread instead of replying on old resolved ones, this would make the issue status tracking easier, thank you.

View Article


Re: Queries about AD7606 Anti Aliasing Filter

soft reminder...Could someone help with my queries?? thanks! Br,Wayne

View Article

order free samples

I want to order some free samples from Analog Devices. But when I add samples to sample cart, it didn't work. Please help me. Thank you! The following was prompted to me:We have been unable to validate...

View Article


Image may be NSFW.
Clik here to view.

Re: The pipeline latency of AD9639?

Hello Jonathan, Thanks a lot. It is very helpful. Best regards,Wei

View Article

How do the device EVAL AD5933EBZ is able to calculate the unknown impedance's...

How do the device EVAL AD5933EBZ is able to calculate the unknown impedance's magnitude and phase using DFT ??? How the real and imaginary parts of DFT are helpful in determining the magnitude and...

View Article


Re: AD7626 Application

Hi Zhouzhx,      Please make sure that there is a good filtering at your input signal. The ad7626 is a 10MSPS ADC with wide bandwidth. What input frequency are you using? If you are using an input...

View Article

Re: GSR/EDA with AD5933

Hi Mike, You can refer to refer to this documentation: http://www.analog.com/static/imported-files/user_guides/UG-364.pdf for more detailed guide on how to use the evaluation board. The electrodes are...

View Article

Re: How do the device EVAL AD5933EBZ is able to calculate the unknown...

Hi Nikhil, Have you checked the datasheet already. If not, I'd like to suggest to read it first, since a brief explanation about its theory of operation are being explained in there....

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>