Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: AD9257 Expected VIN Load

Hello Mr. Foote, The 100Ω terminations for the clocks are to comply with the requirements of the respective signaling standards (e.g. for LVDS, etc.). The analog input pins of the AD9257 are...

View Article


odd ad9361 noos/linux behavior at < 8.215 Msps

Hello, I am using an fmcomms3 + zedboard. I am attempting to run the ad9361 at a lower sample rate e.g. < 10 Mhz. Using the sd card shipped with the fmcomms3 (using AD provided fpga + linux drivers...

View Article


Re: Re: port uboot on custom board based on bf548-ezkit(new bee)

Hi Aaronwu,     Thanks for your helpful suggestions.Finally I successfully port my uboot on the custom board .Correct board file is attached  (at least for me).     thanks!

View Article

Re: Re: Re: HDMI configuration(ADV7511)

Hi GuenterL, As per your reply, I have changed 7511 I2C main Regiser 0x15[3:0] = 0,  Display colour is now chenged but its not clear.  Three snapshots are attached for your concern. Note:    16 bit...

View Article

Re: AD 9246 Evaluation Board HSC-ADC-EVALB-DCZ

Hello, Can you attach the FFT spectrum for the same input and clock signal? the distortion in the input is probably some impedance matching issue. Make sure the Waveform generator's output matches the...

View Article


ADV7611BSWZ-P and ADV7611BSWZ-P-RL

Hi, In the datasheet of ADV7611 (Page-14) , ADV7611BSWZ-P part is mentioned as a non-HDCP version. However, ADV7611BSWZ-P-RL part is not mentioned as a non-HDCP version. Can you please confirm if...

View Article

Image may be NSFW.
Clik here to view.

ADAU1452 Master Control Port

Hi there.  I want to boot a codec (AD1939) over the master SPI port of the ADAU1452. When trying to drag, drop and configure the 'Master Control Port I/O' block in Sigma Studio (3.10.4 or 3.11 beta) I...

View Article

Image may be NSFW.
Clik here to view.

Help with part selection for audio mixer

Hi, I'm planing the design of a small remote controlled audio mixer that allows mixing of microfone inputs as well as sound from a connected BeagleBone board. The mixer should have: Inputs:2 Microfones...

View Article


Streaming tx with AD9364

Hi, We wish to stream some data out of the fmcomms4/AD9364 board. Luckily, we found that there is a piece of sample code  Re: AD9361 Streaming Transmit. We disabled the cyclic bit, downloaded the...

View Article


Re: Auto Sleep Mode in ADXL313

Hi Tao, I did not have ADXL313 in hand to double confirm your condition. But I have tried other similar part ADXL362, below is the test result.1. DATA_READY interrupt can be generated in sleep mode. Of...

View Article

Re: problem with ADXL345 outputs

Hi, 1. Please try to make sure you can read DEVID (register 0x00) correctly.2. Try to write a R/W register and read back to make sure there is no probelm on writing/reading the register.3. When you...

View Article

Image may be NSFW.
Clik here to view.

Can't selfboot with EVAL-ADAU144XEBZ board

Hello, We bought a evaluation board(EVAL ADAU144XEBZ REV C).  We had some issue on selfboot function. Please help to find what's wrong with our action. STEP 1:  We build a project in SigmaStudio as the...

View Article

AD9361 VCO calibration lock

HI guys. I work with on AD9361(FMCOMMS2) with my XILINX-V6 board.I make it work on FDD mode and the REF_CLK is 40MHz, and the working frequency is 2.45GHz. I follow the instructions of the...

View Article


SEC Self-nesting on BF-70x

Hi, I have a question about SEC(System Event Controller) self-nesting interrupt. For instance two timers (timer0 and timer1) are set in SEC interrupt source (SEC Priority : timer0 > timer1). When...

View Article

GP Timer EXTCLK mode on BF70x

Hi, I have a question about GP Timer EXTCLK ( clock source: SCLK) on BF70x. I want to start free run timer counter on BF70x Ezkit, but the timer never count up SCLK clock. My source code is below. void...

View Article


Re: Porting of AD9361 to Altera FPGA

Hello Robin, Charly & the rest of the team Was there any progress with the porting of the HDL to Altera?We have some customers who are looking for this. BR,Alon

View Article

Problem installing EVAL-ADISZ / 16210 with IMU evaluation software

Hello, I have followed the instruction on the wiki regarding the installation of this board but the board is not seen by the system. The Led L2 is only blinking very weakly (it goes on an immediately...

View Article


Image may be NSFW.
Clik here to view.

Re: ADF4159 - Example of a staircase waveform

hi rbrennan,I am using ADF4158 eval board now,I am just a learner and I want to know how to generate a ramp FSK waveform,how do i set Analog Devices ADF4158/4159 PLL Software.Can you help me?Thank you

View Article

Re: pspice modelling of thermistor

Hi indu1, I'm not sure what is your question here, whether you want us to comment to comment or check on the circuit. Regards,Lluis.

View Article

Image may be NSFW.
Clik here to view.

Re: AD5622 I2C Issue

oh sorry, DAC is at address 0x0E. I've also measured rise time, Vol, and timing...

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>