Re: Algorithm to suppress self-excitation?
Hi Miguel Thanks for your help. May I know when the next SS will be published? BR,Jackie
View ArticleRe: AD7626 Bit error in the output
Hi, thank you all again for your efforts but I solved the problem. It was a mistake in the data processing. The first high byte was not transferred and thus I scrambled the high- and low-bytes of the...
View ArticleRe: ADF4351 basic problem.
The screenshot says 'No device connected'. Please examine UG-435 on instructions to connect your PC to the ADF4351 evaluation board.
View ArticleRe: Power-up sequence of AD5683R
There is not restrictions in terms of ramp rate, as far is something "normal", we didnt test the part with a 10s ramp rate or non-montonic supply rate. As far as I remember, the only restriction is to...
View ArticleAD9361 FIR setting problem
Dear Sir, If I used a filter by matlab(64tag/BW:56MHz) and how could I import to AD9361?Many thanks! The souce code as below: % Generated by MATLAB(R) 8.1 and the Signal Processing Toolbox 6.19.%...
View ArticleRe: ADF4351 basic problem.
Yes i am not using UG-435 board (ADF4351 eval board) and i designed custom board as per my application.By using this GUI first i am sending same commands by my controller/processor.But i am not getting...
View ArticleClik here to view.
SPI Clock setting in ADF4351
Hi, I am using ADF4351 in my circuit. For this i need to set 6 registers through SPI protocol. But different time limit has given in datasheet for clock input like below mentioned diagram .But we...
View ArticleRe: AD9517 SPI with AD9467FMC
Hi Rohit, To use the external clock source (SMA connector J201), you do not need to make any modification on the board. It will work as it is. If you want to use the AD9517 or/and the optional OSC...
View ArticleRe: Repeater APP ported
Hi Dani,Which software version are you using? Are you using Blackfin based or ARM based platform since we use different main files for each. Regards,Poornima.
View ArticleClik here to view.
Re: Problems obtaining output on teh BF527 LCD for LCDColorBar example
Hi David sir, I agree your point ,for program was running successfully,but the LCD display still off state. whatido sir.......ihave get new response debug window if idoesn't press start...
View ArticleRe: Offset LVDT Conditioner AD698AP
Hi Chris, This is the AD698 output in attachment, we adapt [-10V / 10V] to [-1.5V / 1.5V]. This is in attachment the information about the LVDT (schaevitz 010-MHR, 10KHz) . We are not using the full...
View ArticleRe: Repeater APP ported
Hi Poornima, I believe Dani is looking at the source code for EVAL-ADV7612-7511P which uses BF524. -Matt
View ArticleRe: AD-FMCJESDADC1-EBZ reference design not working with ZC706?
I updated: http://wiki.analog.com/resources/fpga/xilinx/fmc/ad-fmcjesdadc1-ebz#supported_carriers Does that help?
View ArticleRe: ZC706 mouse and keyboard connection
http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/quickstart/zynq#setting_up_the_hardware_zc706
View ArticleRe: Smearing problem when use ADA4858-3 driving and equalizing a 100M VGA cable
Hi Ahbie,Many thank for your reply.We will have a try to change R109 (56R) to 15R at first. What's more, In the previous exisiting actual circuit, R116 was NC, and the ADA4656-3 R/G/B output were...
View ArticleRe: AD1934 Hardware Setting Issue
Hi Paul, Please refer to the User Guide for the AD1938: http://www.analog.com/static/imported-files/user_guides/UG-045.pdf The footprint is identical, and the circuitry for the power supply, PLL...
View ArticleRe: AD9361 Fast AGC mode question??
"AGC Lock Level" is typically set to -10dBFS. You have to set the threshold levels correctly. The gain will be adjusted by AGC as close as possible to the AGC Lock Level. RSSI depends on the gain...
View Article