Re: Accelerometer and output device for high school physics project
Neil, Thanks for the reply. I looked at the info for both the ADXL375 and ADXL001. I am totally out of my field here. Is there a product already developed that uses these types of accelerometers...
View ArticleADV7611 ESD testing
Hi, I'm currently using the ADV7611BSWZ on a new board and I'm having some issues with it when we do ESD testing on the unit that its in. When we do contact discharge (as low as 3KV) to our unit, we...
View ArticleRe: Problem Booting from Target when using AD193XX module
Hi Everyone, I found a solution! If I simply delete the USBi module and drag and drop another in its place, it will boot from the target just fine. Not sure why that works, but i'm happy I can move...
View ArticleRe: ADV7842 ： How long should the wait time be estimated for TMDS PLL reset?
Hi GuenterLThank you quick answer.and sorry late response.I appreciate it. Thank you.Best regards.aimPoint
View ArticleRe: Can ADV7401 output 720p@30fps analog component with 8bit-4：2：2(DDR mode)?
Hi Ray-san, Thank you very much. Best regards.
View ArticleBF592 EZ Kite Lite SSM2603 max SAMPLE RATE 96000
Hi, im working with the BF592 EZ KIT LITE.I just made a few tests with the audio test programm.I tried to realize a signal generator which uses both outputs and the left and the right channel.It worked...
View ArticleRe: zc702 HDMI broken after update
I had been using the xcomm_zynq kernel branch, according to the information on the wiki (http://wiki.analog.com/resources/tools-software/linux-drivers/platforms/zynq).Using the...
View ArticleRe: AD9129 Evaluation Board & Xilinx ML-605 Reference Design Questions
Reposting my question. Is there a similar register I can write to which allows me to change the digital amplitude of the tone?
View ArticleRe: Alternative for AD8302
We do not have another phase detector exactly like the AD8302 but with better bw, but we do have the IQ Demodulator ADL5380 that has 390 MHz of baseband bw. You would have to sample the I & Q...
View ArticleRe: ADuCM360.IOVDD. Can I use 1.8V as IOVDD ?
Hi Alex, Thanks for your devoting experiment.And Could you check following my experiment ? Phenomena and views. 1. I've supplied IOVDD = 1.8V and AVDD = 3.3V with Laboratory Power supply without LDO...
View ArticleSPORT stream in simulation reading only LSB
Hello All, I am trying to simulate ADC data coming in to a 21488 via a stream to SPORT1A from a file consisting of a series of 1000 or so theoretical ADC samples given in hex. I got the sample rate...
View ArticleRe: Can ADV7401 output 720p@30fps analog component with 8bit-4：2：2(DDR mode)?
Hello, Thank you very much. Best regards.
View ArticleHow can I get the BF518 demo kit for AVB with the LabX AVB software?
Im looking to get the BF518 demo system thats been put together for AVB and includes a demo of the AVB LabX software.Where from? I cant find it anywhere.
View ArticleRe: SPORT stream in simulation reading only LSB
I just figured it out! I had SLEN set to zero in the SPCTL1 register! Now it's working exactly like it should and I can move forward with my code development!
View ArticleSynchronizing multiple AD9517-1
I am using the AD9517 on two boards, and i am trying to synchronize all outputs such that the phase/timing between outputs on both board are repeatable at every power-up or reset cycle. I have made...
View ArticleRe: What is the failure mechanism of AD9361
Testing was performed using a source delivering power measured in dBm units. It has not been investigated whether failures are due to power or voltage. It is recommended to provide fast acting...
View ArticleRe: AD8131 and AD9461
Hi, If you plan on DC coupling to the AD9467, then you will have to have a signal biased at 2.1V. I am not sure if the ADL5201 will be able to DC couple too AD9467. As an alternative, you could try...
View Article1/f noise vs RMS an peak-peak calculation
Hello, I am in the subject of measuring mV signals with maximum accuracy.The formulas for calculating white noise is described in several data sheets.But for 1/f noise I didn't see such a formula....
View Article