Re: how to get total harmonic distortion ................
Hi hmani, I have assigned HX=2,HY=3,and HZ=4 then the register reading is Register Values HXVHD0.071HYVHD0.467HZVHD0.046VTHD...
View ArticleRe: Can ADXL375 BW_RATE register be set to '1111' and still operate I2C at...
Hi cdarrow, It is totally fine to set ODR = 3200Hz for your application scenario. You can use trigger mode FIFO to record the whole shock or activity profile. Then read the data through I2C interface...
View ArticleRe: ADV7611 :Hdmi signal not detecting in ADV7611
Dear Venkatesh, kindly suggest the what is the hardware issue did you faced in HDMI receiver(ADV7611).Because i am facing the same problem what you mentioned(HDMI input signal not detecting in...
View ArticleRe: AD5504 works, unless I have more than 1
Hi MTJones,I don't know of any reason why it shouldn't be possible to write to multiple AD5504s. Are you writing to the AD5504s individually (individual /SYNC per part) of multiples at once (common...
View Articlehow is the function of the i2s digital out
Hi I will connect an salve to the adau1701 in i2s mode. the resolution should be 16 bit.what must i config wiht the sigmastudio? thanks for helpinghubijo
View ArticleRe: High School Science Project Question about Op Amps?
Thanks Jonathan for the reply. I guess my son and I have a long way to go for learning more about circuits.
View ArticleRe: ADXRS624 - Lowest Rate ?
Dear NitzanInitiallyI want tothank you for thebeautiful answer,andteachingabout thedatasheet.For myapplicationa minimumangularrate of 0.05º/sis enough, butfromyour informationI believeis inevitableto...
View ArticleRe: AD9129 Evaluation Board & Xilinx ML-605 Reference Design Questions
Yes, it needs to be corrected- will do. However, you said the DLL is not locked, that would mean the data was sampled incorrectly. I am a bit confused, can you try clearing that error and see whether...
View ArticleClik here to view.
Re: how is the function of the i2s digital out
Hello hubijo, Here's the settings I have used to transmit I2S audio from a -1701: The MP pins are set up for Output Sdata 0 and 1 at MP6 and MP7. MP10 and MP11 provide your I2S clock...
View ArticleRe: AD2128 problem with audio breaking through open switches
The input signal we have used Sean is a headphone level signal. <8v I believe
View ArticleRe: ADUM3190 Operation at -55 Deg C
David: We have not tested our product for these mil std tests. The product was released in the past year and may not have had time yet for someone to use it yet in a military/aircraft system. If you...
View ArticleRe: AD9958 internal reference clock with 25MHz Crystal
Hi jonasz, I think you should also take off C21 and C22 because they are also tied off to the ground. They could have change the load capacitance of your crystal. RegardsLouijie
View ArticleRe: AD9958 internal reference clock with 25MHz Crystal
Hi jonasz, I've answered this on your first thread. ThanksLouijie
View ArticleRe: exact protocol to configure ic ad9959
Hi rahul, I just want to ask the kind of protocol you are referring. Are you talking about the digital interface protocol? Or the protocols above the physical layer? And on what kind of application is...
View ArticleRe: parallel byte interface mode of AD7606
Hi, Kou. I suggest you follow the datasheet recommendation of grounding the DB[13:9] pins when PAR/SER/BYTE SEL=1. As I mentioned, the part could work outside of these conditions, however, we could not...
View ArticleAD9559 : Frequency Clamp
Hello, I have a question about AD9559 device.I cannot find the formula to calculate the frequency clamp function in AD9559 datasheet.Please let me know the formula and some information about the...
View ArticleRe: INT1 and INT2 on adxl345EB
Hi Ebtehal, Please leave INT1 and INT2 open, no connect if you did not use the interrupt.Thanks. BRNeil
View ArticleRe: ADV212 16bit-RAWPIXEL and JDATA mode problems
Hello DaveD Now I want to use ADV212 to compress a series of 2048 * 1024 images. Here are my questions: 1). How could I decompose a image? I find the maximum size a tile can contain is 512*512 in this...
View ArticleRe: ADV7612 with SONY DVD player BDP-S490 sync lose issue
Dear Jeyasudha, I have sent the player to concerned team in Ireland. Even we thought that the issue may be cause by SONY DVD player, but our customer's platform have another HDMI Rx (Himax HX6A29) at...
View Article