Re: ADXL375 evaluation board's behavior at ODR=1600Hz,3200Hz
Hi Moto, I did not get your questions. The Real Time Data tab of ADXL375 just show the real time output from ADXL375, no post processing. Or say, just use xxxLSB * scale factor and using the scale...
View ArticleAXI AD9361 DAC DMA HDL
Hi, I'm trying to implement some flow control on the AD9361 DAC DMA in the HDL reference design. I have my own module that processes data that is output by the DAC DMA. Essentially, I need a way to...
View Articleuse cces and sigmastudio simulat ADSP21489 problem
Hello: I use the usbi by sigmastudio simulation adsp21489 development board is no problem, use example LDR files.Now I use USBi simulation target board, I by modifying this routine LDR file in cces...
View ArticleRe: Readback gain reduction of Dynamic Processor with ADAU1452
Thank you KJBob! I will give both of these a try and report back on how it goes. I do appreciate the help!
View ArticleAD7708 absolute ratings
Hello there, I have a question about the absolute ratings of the AD7708.According to the datasheet: AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . . . –5 V to +5 V Typically, in my design:...
View ArticleRe: adv7180 pal capture interlaced issue
hi dave, I want to capture in 576I mode not in 576P ,as your are saying 720x288 per field i want to get per frame two filelds ,so total i may get 720x576 as frame. regards,karthik
View Articleinquiry about xilinx2014.4-linux-AD-hdmi-zedboard
hello I'm using vivado2014.4 on win7-64 and virtual ubuntu14.04-64 bit. I want to build linux with hdmi on zedboard to run Qt app. I download the xcomm_zynq linux kernel in zip at site...
View ArticleRe: ADE7953ACPZ Application/References Schematic
Hi dlath, Thank you for your response.Indeed, those two documents are good and quite complete.But, just like I said. Since it's for evaluation board and this is my first time for design a PM chips,it's...
View ArticleRe: How to program AD5686R Evaluation Board SPI using arduino mega 2560?
Hi, Darren. Have you made changes in the board (removing or adding or changing any parts)? If you did, could you state all of them? Could you also take a photo of both sides of the board? Regards,Mark
View ArticleRe: libiio python bindings crash
Adam: Thanks for the update. We will do when Paul gets back. - Robin
View ArticleRe: Changes from ad9361 to ad9364
This is what we do for the FMCOMMS4 (based on the AD9364). - Robin
View ArticleRe: AD8606AR MTBF
Hi Clive, We don't specify MTBF in our devices. However we can provide another reliability measurement that could help you with your requirements. I suggest you consider MTTF data for MTBF. I believe...
View ArticleRe: Labview source vi's for AD7173-8 eval
Hi knap,I have sent you the Email, let me know if you need anything else. Regards,Jarwin
View ArticleRe: Labview source vi's for AD7173-8 eval
Hi Jarwin, We have not received your email. Hope I didn't throw you off with the way I've got the email displayed. Thanks, knap
View ArticleRe: How to program AD5686R Evaluation Board SPI using arduino mega 2560?
Hi Mark,No changes to the board &No parts removed or added. Photos
View ArticleRe: [AD5061] Datasheet typo? (Vbf pin doesn't exist)
Hello,Thank you for your response!I understood that. Best regards,Sofy
View ArticleRe: BF-561: Building Linux 3.10 kernel
Hi Kevin, please use one of our official release to start with, usually the latest release, now it's 2014R1. If you are having problem based on one of the release, please share us information for your...
View ArticleRe: AD7513 - 1080p/30?
After digging around on the blogsite for a bit, I began to suspect that the 'E PAD' under the ADV7513 wasn't properly grounded. Sure enough, I was able to de-solder the device from the PCB and saw that...
View ArticleRe: ADIS16305 SPI problems
Some quick ideas: 1. make sure that the reset line is not being loaded down2. perhaps it would be good to read a single register, like PROD_ID first3. Check supply current. Is it near the specified...
View ArticleRe: Crystal Oscillator on AD9852 eval board
Hi Mashak, Based on the schematic of the board, you must transfer the jumper of W17 to 1 to make the crystal supply clock signal to U3. W3 is for enabling the differential clock. You can return the...
View Article