Re: BF609 PVP color separation
Hello, Not sure what you do mean by "color seperation only is supported for monochrome". Monochrome is luma format with no color information. If are saying this is mentioned in HRM, please let me know...
View ArticleRe: ADAU1701 DSP Latency
Hi Coleman, I am having issues with the ADAU1701 which I suspect is due to latency, I'm implementing an Active Noise Reduction system for a headphone with the DSP to compensate for the speaker's...
View ArticleCan AD8475 configured to a gain other than 0.4 & 0.8 using external resistors
Hi, I am working on multi-channel DAS. I am using AD7982 in the signal line. The dynamic range of this ADC is 5V p-p differential with a reference of +5V. The receiving signal dynamic range is 20V p-p....
View ArticleADIS16250/ADISG16265/ADIS16364 Can I read/write registers 0x00,0x7f without...
We've been using ADIS16250/ADISG16265/ADIS16364 for many years here. This will seem like a funny question:Can I read or write the following non-existent registers without causing any problem in the...
View ArticleDoes NO-OS software support Xilinux ML605 LCD?
Does NO-OS software support Xilinux ML605 LCD display?
View ArticleRe: Trouble with No-OS Project for AD-FMCOMMS1
Hi, Sorry for the late answer. Many of our team's members were on vacation on the last days. I will take a look over the mentioned problem and I will tell you the solution. Regards,Dragos
View ArticleAD8366 Output Common-Mode control
Hello, I am planning to use the AD8366 to drive the dual inputs of the AD9643 ADC. From the AD8366 datasheet, it seems that output common mode voltage is programmable from 1.6 to 3 V only. But by...
View ArticleRe: Does NO-OS software support Xilinux ML605 LCD?
Hi, Until this moment, the LCD display from the Xilinx ML605 was not used by any of the no-OS projects. Regards,Dragos
View ArticleRe: Select Temperature Sensor
Hi Rob, Thanks for your reply. Two questions for ADT7312: 1.The temperature is lower than +100C in our application, if the temperature reaches higher than +200 or even +300C accidentally, it will not...
View ArticleRe: ADV7850 : Autographics DE register settings
Hi Alan, As far as I can tell that is not a standard in CEA861F so DE is not defined. The values were either determined experimentally from a source or picked from whatever standard they had for it....
View ArticleRe: ADP2108-3.3 Cannot deliver more than 200mA
Hi Deon, As discussed offline, I am sending you a few samples to swap out and see if they work. In the meantime, I'm looking at your layout, and am guessing C2 is your output capacitor. Where is the...
View ArticleClik here to view.
Re: Capturing XGA (1024x768@70Hz) with SOG using ADV7403
Well that's true if you ignore the secret mode that Analog Devices removed from the datasheet but is still implemented in the ADV7341?
View ArticleRe: Capturing XGA (1024x768@70Hz) with SOG using ADV7403
If the ADV7341 evaluation board works for you, great. Otherwise, I would suggest using the ADV7403 evaluation board which has ADV7403, ADV7341, and AD9889B. -Matt
View ArticleRe: Capturing XGA (1024x768@70Hz) with SOG using ADV7403
Thanks for the tip! I'll take a look at it.Ian
View ArticleRe: Capturing XGA (1024x768@70Hz) with SOG using ADV7403
(Just to follow up; I have finally gotten the RGB input with SOG modes to work with proper sync. I had to- Adjust SOG level- remap the AIN/ADC assignments (ADC0-> AIN6, ADC1->AIN4,...
View ArticleADAU1452 evaluation board Manual and Schematic
Please the ADAU1452 evaluation board Manual and Schematic
View ArticleADV7391 with 2.5V I/O
We are using the ADV7391BCPZ video encoder and want to confirm that 2.5V I/O voltage is stable with this chip. We have a rev-1 prototype that may have a flicker once in awhile in the composite video....
View ArticleADV7842 Pixel and Output traces, 75 ohms?
In UG-214 (Rev.0), page 488, Figure 175: "ADV7842 Pixel and Output Pins":it shows 75-Ohm resistors, and says "Traces to be impedance matched to 75 ohms". In regards to the lines on the left side (P0 -...
View Article