Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: AD9361_Initialization

Hi Dragos , Thanks for the help but I tried a build with the latest code base you mentioned with FMCOMMS4 connected to FMC1 port and clearing two_rx_two_tx_mode_enable flag , it is still giving the...

View Article


Re: EVAL-ADCMP565 as trigger circuit

Thank you very much, Kris!! Regards,Sam

View Article


Re: SHARC 21489 SPI Master Boot Problem

Hi Klaus,Sorry for delay in getting back on this. I have done the experiment with ADSP-21489 and concluded that the first value in the loader file need not to be 0xA5. It can be anything, and this 32...

View Article

Re: ICPLBMissWithoutReplacement error -- while DMA memory transfer

Hi, I have tested the same code by running in BF609-EZKit lite. No such problem occurs.So I doubt in my custom board design. and also ,During the exception, stack pointer is corrupted. it is 0x7FA0 or...

View Article

Re: Why PAL Video work good but RGsB Video does not?

Thank you for your attention when connect rgsb signal to a standard monitor (with green and gnd signal) when a noise occur monitor display go off and on again (TFT Controller start automatic detection...

View Article


Image may be NSFW.
Clik here to view.

Re: AD8336 Output signal level

Hi Kris, Thank you for your advice.I tested under the following conditions, and got the desired results.Vgpos=0.662VVgneg=0.75VVGAgain=-0.088V Could you please teach me control method when I make the...

View Article

Re: AC701/FCOMMS3 axi_ad9361 ip mods for custom no-os implementation

AdrianC You are right on! That was the problem with the interrupt concatenation module. As far as the timing goes, the rx_clk path (as constrained to 4 ns in system_constr.xdc) is the one that is...

View Article

Axi_dmac optimized issue?

Not sure if there is a list of know issues, but I seem to have a unique one. The DMAC is in source = fifo , destination = axi_mm.The eot signals are complelety wiped out, running dont_touch and...

View Article


Re: HMC536 Control Voltage Spec

Hi Kevin, The control voltages biased the internal series and shunt FETs, therefore the voltage level will determine the RF performances and power handling of the HMC536. We recommend a tight tolerance...

View Article


exporting data from ADAS3022

Does anyone know how to export data from the ADAS3022? The software has an export option, but there's no default file type, resulting in a file that can't be opened. I tried saving it as a text file by...

View Article

AD9364 charge pump current and bleed current

The AD9364 Reference Manual, UG-673, says that the BB PLL charge pump has "programmable output current from 25 μA to 1575 μA in 25 μA steps. In addition, a programmable bleed current is available. This...

View Article

ADAS3023 undocumented behavior

Hello EZ, We have successfully managed to get the ADAS3023 to work as described by the timing in the datasheet; however there are some observations and undocumented behavior that we would like ADI to...

View Article

ADE7880 input overvoltage behavior

I have been using the ADE7880 and it has been working fine with the exception of its behavior when the input goes above about 0.65V. At this point if you look at the raw voltage and current data you...

View Article


Re: AD1853 introduces spurs when given a DC offset?

Thanks, Dave, Some observations:- we observed the tones at 192 KHz as well at 96KHz; in our applications we use varied fSAMP values, such as 100KHz,  65KHz, 50KHz, 25KHz etc.- we generate  signals with...

View Article

Re: FMCOMMS4 Board and dac_valid signal

I moved this to somewhere where people monitor, so it will get answered. -Robin

View Article


Image may be NSFW.
Clik here to view.

Re: ADC Channel IP core in AD9364 reference design

I moved this to somewhere where people monitor it. -Robin

View Article

ADAS1000 Digital ports currents

Hi, all.Please let me confirm.If ADAS1000's digital ports are flowed 2.5mA, ADAS1000 will be broken?I'd like to connect photocoupler to SPI ports and photocoupler recommends to be flowed 2.5mA.When I...

View Article


Re: AD9364 charge pump current and bleed current

Current in 0x046 is not CP bleed current, it is CP current. The provided device drivers configure the AD9361/4 for a given set of parameters. Charge pump configuration is part of this configuration. 

View Article

Re: AD9364 charge pump current and bleed current

When you say "charge pump configuration", does this also include any configuration for bleed current? Is BBPLL bleed current customization something that ADI doesn't want customers to change?

View Article

Image may be NSFW.
Clik here to view.

Re: IIR filter crashes on the fly

     Hello Dan,      Thank you for your kind reply.  It appears you have the microcontroller end of things well in hand.  Thus your safeloading routine is operating consistently as you have verified....

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>