Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: About ADE7953 problem with temperature?

Hi dlath This -0.04 % error about reference meter? You mean the specifications on the ADE7953 INTERFACE AND EVALUATION BOARDS? Regards,Kuanish

View Article


Re: ADA4870 high output current op amp

Hi, sadegh. Can you please share your schematic so I could simulate it and so we could easily pinpoint the errors?  Regards,Anna

View Article


Re: AD7763 SYNC Signal

Hi Jim_Jim,           I am looking into this. I'll get back to you soon. Regards,Jonathan

View Article

Re: Help to find solution

Hi,  We have some reference circuits for pressure and temperature sensors over at Circuits from the Lab. Please check the portfolio for your reference. Hope this helps. Regards,Karen

View Article

Re: AD9910 Intermittent outputs or just broken

Hi Steve I think the 246.5 MHz frequency corresponds to the SYNC_CLK signal. Try disabling the this signal at the registers and observe if this situation still persists. Best RegardsLouijie

View Article


Image may be NSFW.
Clik here to view.

Questions on ADI REFERENCE DESIGNS HDL

Dear all, I am preparing the HDL driver for Vivado. My project is about to develop an application on the platform of Zedboard and FMCOMMS3. I find that 4 kinds of branches are available. What is the...

View Article

Re: ADV7611 IIC

Hi,        Thank you very much.I have fixed this problem. Because if i read the adv7611 , firstly I write the salve address and subaddress without P, then I write the salve address.  The picture above...

View Article

Re: LabView source for EVAL-CED1Z + EVAL-AD7621 kit

Hi, We can provide the source code for your reference but we can't support any changes you want to implement. The codes can be downloaded here:  Please let me know when you've downloaded the file....

View Article


Re: ADE7763 readings at low power factor and low current

Hi hmani,     Yes you are correct we are using line accumulation mode for energy measurements. Right now we are using 250 half cycles for accumulation. I will increase the number of cycles and check...

View Article


Re: ADAU1442 with Two ADAU1701

Hello John, Thank-you for your early reply.I did consider the ADAU1451 and the AD1938 CODEC.The ADAU1451 is a new part and the algorithm libraries are not completely available/ported yet. If AD updates...

View Article

Image may be NSFW.
Clik here to view.

Sigma 300 (ADAU145x) Slew Volume Rates

     Slew volume controls can filter noisy control inputs and minimize clicks.  Often the desired slew rate can be found by experiment.  However, in some applications it would help to know the actual...

View Article

how to config Gm mixer sub table?

I have a code for this config. But I don't know the value of gain, bias, control mixer? please help me!

View Article

AD7150- Issue with data logging

Hi all, I am using AD7150 Evaluation Board, when I log data using "Log Data to File" for a capacitance of 10pF ceramic capacitor the value show in GUI is 10.1766 and the value shown in text file is...

View Article


Questions about AD5422

Hi there, I have some questions about AD5422.It would be helpful  if somebady helps me with my questions. #1,About Latch pin,I want to update writting datas (control register,  DAC data)  and want to...

View Article

Image may be NSFW.
Clik here to view.

Re: ML605+ADFMCOMMS3

Hi,Adrian,  I settled  the  ERROR:NgdBuild:604 - logical block  problems by commenting the followings inaxi_ad9361_dev_if.v: But during the map process,I had an error:ERROR:MapLib:1114 - IDELAYCTRL...

View Article


Image may be NSFW.
Clik here to view.

Re: Questions on ADI REFERENCE DESIGNS HDL

Hi Csoml, Today I chose the libraries and projects under the branch of hdl-hdl_2014_r1 . I tcled the all libraries and system_project under fmcomms2 directory. However error came as follows, could you...

View Article

Re: ADP1048 max output power?

Hi Alex, You can just change the shunt resistor. If you change the resistence by half, you can dboule the power rating. James

View Article


Re: AD7609

Hi, Sathya. I can't see the AD7609 portion of the schematic. Did you follow the layout guidelines stated in the datasheet? Are you seeing correct voltage on the REGCAP pins? What reference are you...

View Article

Re: Questions about AD5422

Hi, Tarzan-san. The LATCH pin is a positive edge sensitive pin so connecting this to GND will make it impossible to send instructions, read, or write to the part. As for the CLEAR pin, if it is not...

View Article

Re: Use ADAU1452 in embedded system - remote control via SigmaStudio (TCP/IP?)

anybody?

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>