Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: Looking for a replacement for PE4312MLBA-Z

Hi Eamon, Your mentioned 6-bit Digital Attenuators, HMC624ALP4E, the HMC542BLP4E and the HMC792ALP4E, are  all potential replacement candidates for the PE4312MSLBA-Z, with very comparable performances...

View Article


Question about AD5933-EBZ

I'm physics student at Dalhousie University.My current project is related to measuring the impedance versus frequency of target circuits and, ultimately, lithium- ion batteries.The AD5933- EBZ is a...

View Article


Re: position aberration of LP & LC package products after reflow soldering

Hi Akira-san, We have an application note on "SMT assembly for Leadless Package" that includes our recommendations on the land pattern, the stencil openings, the reflow temp profile for various LP and...

View Article

Re: About RF Pin of HMC346G8

Hi Tomohiro-san, Can you please clarify if your inquiry on the max voltage applied at RF ports are related to the normal signal condition or the possible RF/voltage transient level? The RF ports of the...

View Article

Re: FMCDAQ2 and FMCADC2 availability

Thanks David. Dave/Charly - Am I correct in assuming that these JESD204B FMC-XXX-EBZ cards will only work in the Xilinx eval boards FMC-HPC slots as the FMC-LPC slots only have one Gigabit Transceiver...

View Article


Image may be NSFW.
Clik here to view.

Re: AD9915 Evaluation board: Reference Clock Power Limits ?

Hi,For ADCLK925, input differenctial range is: 0.2Vpp to 3.4Vpp.In dBm (50 ohm system), that is from -10dBm to +15dBm. To verify, I have checked by bench test.The ADCLK925 can go as high as +17dBm. The...

View Article

Re: AD5933 and AD5934 evaluation board software commands

Hello every1, I have purchased new AD5933 board.Can any1 guide me how to calibrate it?And how we choose the value for RFB and calibratation resistor?I'm using PZT piezo sensor to measure the impedance?

View Article

Re: About the noise of ADAS3022

Hi,KarenNE Thank you for information.However, it is that of the noise is not improved.I will attach our customers of the measurement environment.Please make sure there is a mistake in the method of...

View Article


Re: AD5933 and AD5934 evaluation board software commands

Hello Sumit, musach provided a LabView Version ftp://ftp.analog.com/pub/evalcd/ad5933/Source%20CodeIt works with me. I'm using 200k RFB and 200k calibration resister, runs on Win8. Best RegardsJialiang

View Article


Re: Where is the Hardware Trace?

Ok, it was actually CONFIG_DEBUG_VERBOSE in linux config.

View Article

Re: VisualDSP++ 5.0: problems with union in Expressions window

Does CCES show the same issue?no improvement between VDSP++ 3.0 and CCES. I wonder why a customer shoudl pay money to switch from VDSP++ and CCES

View Article

ADV7842 latency

Hi,     We are planning to use ADV7842 in one of our project which has stringent requirement of end to end latency. Please answer my following questions of AD7842's latency. 1) What is the i/p to o/p...

View Article

ADV7842 latency

Hi,     We are planning to use ADV7842 in one of our project which has stringent requirement of end to end latency. Please answer my following questions of AD7842's latency. 1) What is the i/p to o/p...

View Article


ADV7842 latency

Hi,     We are planning to use ADV7842 in one of our project which has stringent requirement of end to end latency. Please answer my following questions of AD7842's latency. 1) What is the i/p to o/p...

View Article

Architecture introduces noise to the signal chain

Hi, We have designed and tested a 16 Bit precise Data Acquisition system. In the signal path we have used the circuit as given in the attachment.  With respect to attachment, VBias is connected to...

View Article


Image may be NSFW.
Clik here to view.

How to Acknowledge Internal ADC "Frame Completion Status" without enabling...

Hi All,I am working on CM403 Internal ADC. I have configured ADCC TMR0 to sample @ 64 KHz .Its working fine. In TMR0 frame completion ISR clearing frame completion status like below static void...

View Article

Re: Crash when trying to change filter type

Hi Jonathan: sorry to hear you are having these difficulties. I tried to reproduce the problem you mention but cannot make it happen. Would you mind posting your schematic? Thank you Miguel

View Article


Re: Crash when trying to change filter type

can I send it by email?

View Article

Re: Link register?(ADV7625)

Hi Kikka-san, Thanks for your patience. I was able to reproduce this behavior on my EVAL-ADV7625-SMZ this afternoon. It does seem like strange behavior. I will ask the ADV7625 experts about this and...

View Article

AD9670

To Whom it May Concern, Question regarding the low pass filter frequency.  On preliminary documentation, the low pass filter was supposed to go as high as 26MHz at 80MHz clock.  The SP0 version...

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>