Quantcast
Channel: EngineerZone: Message List
Browsing all 22625 articles
Browse latest View live

Re: ADF4351 PLL programming question

R0: 02D00000R1: 08008019R2: 04004D02R3: 00400003R4: 009012FDR5: 00580005 Int N mode, N=360, Fref=10MHz, O/P div by 2, fund. feedback Thanks,Sk

View Article


Re: Using ADL5380-EVALZ to demodulate to DC

You might want to look at the AD8130 amp.  It will take the differential output, convert it to single ended and be able to drive the 50 Ohm load just fine.  I've personally used the amp a lot and it...

View Article


Re: AD9361 for WiFi (TDD) application

Yes, the delay is ~160ns + SPI write. Flush does not occur because the Enable state machine does not change states in this case.

View Article

Re: Help with BTC for ADSP21369

Thanks Craig,  I carefully studied BTC demo for 21369 and now BTC works in my application.The differences with the quoted description are:1. I do not use btc_poll() - just update BTC channels data with...

View Article

Image may be NSFW.
Clik here to view.

Re: ADV7610 with Freescale I.MX6

Hello, ADV7180 and ADV7610 are completely different.  Not sure how that could work.  The best way to bring up hardware is by using an HDMI test pattern generator and the scripts from the ADV7610 Design...

View Article


Re: Prefetch Abort with Nested VICs?

Making a smaller file that exhibits the problem doesn't seem possible (not sure why cutting out things causes it to not abort...). I did find something though -- I was converting an int to hex using...

View Article

Re: EVAL-ADUSB2EBZ (USBi) support under Linux?

Hi Martin, Thanks for the suggestion but I was able to work with our friends at ADI to get the spec. for the USBi USB protocol. Using these documents I was able to use libusb (under both Linux and...

View Article

Re: Modbus-RTU and Aduc7060

Follow the porting instructions (and customize MSPL_UserIF) and you'll do fine -- you have to write the serial I/O routines (remember the 3.5 char turnaround and handle taking/releasing the RS-485 line...

View Article


Re: BF547 USB - Powering VDD_USB to ensure USB_VBUS input is safe

hi Dale, The 2mA you're measuring could be a contribution of the load hanging off the VDDEXT domain.  Unless this is a USB bus powered design I would recommend only powering VDDUSB from VBUS when...

View Article


Re: BF60x USB endpoint 0

Thanks, Jorge! That is exactly what I was looking for.  However, I don't see this information in the Hardware Reference Manual.  Are all Blackfin DSPs set this way, or is this information located...

View Article

Re: AD9665 mounting image

Dear Jino Thank you very much for your support. I would like to make sure.You means,The exposed pad doesn’t have to connect to ground.That note “The exposed pad should be connected to ground” means...

View Article

EVAL-SDP-CB1Z board with the EVAL-AD9837SDZ board

i am new in this community. i bought the EVAL-SDP-CB1Z board and the EVAL-AD9837SDZ board to want to get sin signal. But i can't get the signal i want to get from the output  pin at EVAL-AD9837SDZ. Sdp...

View Article

AD9361 REF_CLK

Hi, In UG-570, Reference Clock Setup and Operation section there is a condition as 'The level for the clock should be 1.3V p-p maximum..'. what would be the impact if the p-p level is higher than 1.3V?...

View Article


phase shift 45 degrees

Hi I need some help to understand whether this is possible and what parts are needed. the desired outcome is this. 8 RF outputs with sin waves with a 45 degree phase shift.5 V peak to peak amplitude10...

View Article

Image may be NSFW.
Clik here to view.

Re: AD9361 CMOS Mode

Hi Michael, Thanks for the feedback.  Currently I am not using Linux drivers or device tree as I am testing using the no-os drivers and associated HDL.  I have manged to do more testing and it appears...

View Article


Re: ADL5380-EVALZ DC IF Problem

Hi, Eric,     You may be able to get some help on AD7903 drivers/programming examples by posting on the ADC forum: Precision ADCs Benjamin

View Article

How to enable ucLinux USB gadget audio for the Blackfin BF526 EZBRD?

Here are my problems:1.I tried the instructions for the BF527 EZKIT to enable the kernel audio card and USB gadget audio. I got "soc-audio: probe of soc-audio failed with error -22" error.2.If I try...

View Article


Re: ADL5385 evaluation board for IQ modulation

Hi, Mo,     Yes, you can use DC voltages for I & Q inputs (with a 0.5V common-mode bias on each pin), and they will change the amplitude and phase of the RF output accordingly.     As for sideband...

View Article

Re: IF output range of AD 8342

Hi, Bhavishya,     The IF pins on the AD8342 are DC coupled, so IF output will support 25-150 kHz. You will need to use dc block caps as shown in Fig. 56, or use very low frequency transformers at the...

View Article

Re: ADV7513 Settings

Hi Elvin, Do you have one of our evaluation boards for ADV7511 or ADV7513? -Matt

View Article
Browsing all 22625 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>